Abstract:Different ageing treatments have been developed to achieve targeted properties in aluminum alloys through altering microstructures. However, there is a lack of understanding regarding the effect of ageing treatments on the formability of these alloys. In this study, we employed crystal plasticity finite element (CPFE) modeling, in conjunction with the Marciniak-Kuczynski (M-K) approach, to investigate the effects of ageing treatments on the mechanical properties and formability of AA6061 aluminum alloy. The as-received sheet was in the T6 heat treatment state, which was subjected to artificial ageing and pre-ageing, respectively, to achieve two age-hardened alloys with modified precipitation states. The microstructures and crystallographic textures of the three alloys were measured using the electron backscattering diffraction (EBSD) technique, and uniaxial tensile tests were performed along the rolling direction (RD), transverse direction (TD), and diagonal direction (DD, 45° to the RD) for each alloy. The forming limit curve (FLC) of the as-received alloy was determined using the Nakazima test. The dependence of mechanical strength, tensile ductility, and work-hardening behavior on the ageing treatments was clarified. Then, the tensile test results were utilized to calibrate the modeling parameters used in the CPFE model, whereas the FLC predictability of the developed model was validated with the experimental one. In the formability analysis, the effects of the ageing treatment on the FLC exhibit a notable dependency on loading paths, and the pre-aged alloy exhibits better formability than the other two at the plane strain tension state, thanks to its high work-hardening levels. In addition, the deformed textures along the different loading paths and the effects of the initial texture on the FLC are also discussed.

What problem does this paper attempt to address?

This paper mainly explores the impact of different aging treatments on the formability of AA6061 aluminum alloy. The study employs the Crystal Plasticity Finite Element (CPFE) modeling method, combined with the Marciniak-Kuczynski (M-K) method, to analyze the specific effects of aging treatment on the mechanical properties and formability of this aluminum alloy. ### Research Background and Objectives - **Research Background**: The 6000 series precipitation-hardenable aluminum alloys (such as Al-Mg-Si(-Cu) alloys) are widely used in the transportation field due to their high specific strength, good formability, excellent corrosion resistance, and sufficient strength. These alloys achieve a supersaturated solid solution through quenching from the solution-treated state, followed by different temperature aging treatments to form metastable, semi-coherent precipitates dispersed in the matrix, thereby enhancing mechanical properties. - **Research Objectives**: Although there are many studies on the effects of aging treatment on the characteristics of precipitates and the resulting mechanical properties in these alloys, the understanding of how aging treatment specifically affects the formability of these alloys is still insufficient. This paper aims to use the Crystal Plasticity Finite Element method to study the impact of different aging treatments (including artificial aging and pre-aging) on the formability of AA6061 aluminum alloy. ### Main Research Content - **Materials and Methods**: - Three different aging treatment conditions of AA6061 aluminum alloy samples were selected: peak-aged state (T6 heat-treated state), artificial aging treatment, and pre-aging treatment. - The microstructure and crystallographic texture of these three alloys were measured using Electron Backscatter Diffraction (EBSD) technology. - Uniaxial tensile tests were conducted on each alloy along the rolling direction (RD), transverse direction (TD), and diagonal direction (DD). - The forming limit curves (FLC) of the original alloy were determined using the Nakazima test. - **Model Establishment and Validation**: - A Crystal Plasticity Finite Element model was established, combined with the M-K method to predict the formability of the alloy under different loading paths. - Model parameters were calibrated using the tensile test results, and the accuracy of the model-predicted FLC was validated through experimental data. - **Results and Discussion**: - The pre-aged alloy exhibited better formability under plane strain tensile conditions, attributed to its higher work hardening level. - The impact of different aging treatments on the forming limit curve depends on the loading path, and the initial texture also significantly affects the FLC. In summary, this study provides a detailed analysis of the impact of different aging treatments on the formability of AA6061 aluminum alloy through experimental and simulation methods, offering a theoretical basis for further optimization of the manufacturing process of such alloys.

Crystal Plasticity Finite Element Analyses on the Formability of AA6061 Aluminum Alloy with Different Ageing Treatments

Influence of Deformation Prior to Ageing on Fatigue Behavior of Extruded AA6082-T6 Profiles

Effect of ageing treatment process on the microstructure development and mechanical properties of 6082 Al alloy

Effect of the Thermo-Mechanical Treatment of Pre-Ageing, Cold-Rolling and Re-Ageing on Microstructures and Mechanical Properties of 6061 Al Alloy

Multi-scale Modelling of Evolving Plastic Anisotropy During Al-alloy Sheet Forming

Combined Effect of Pre-Strain at Elevated Temperature and Pre-Aging on Aging Strength and Microstructures of AA6082

Microstructures and Mechanical Properties of Age-Formed 7050 Aluminum Alloy

Effects of aging treatments on tensile properties and fracture toughness of AA6156 aluminum alloy

Effect of Aging Treatment on Microstructure and Mechanical Properties of As-Extruded AA6063 Aluminum Alloy

Investigation of formability, microstructures and post-forming mechanical properties of heat-treatable aluminum alloys subjected to pre-aged hardening warm forming

Influence of Cryogenic Deformation and Post-Deform Aging on Microstructure and Mechanical Properties of Al-Cu Alloy

Improving the Strength and Ductility of Al–Mg–Si–Cu Alloys by a Novel Thermo-Mechanical Treatment

Effects of different initial states on dynamic tensile properties and microstructure of 7075 aluminum alloy

Investigation of Pre-Aged Hardening Single-Point Incremental Forming Process and Mechanical Properties of AA6061 Aluminum Alloy

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Influence of aging treatment on mechanical properties of 6061 aluminum alloy

The Effect of Initial Aging Treatment on the Microstructure and Mechanical Properties of Cryorolled 6016 Al Alloy

Mechanical Properties and Microstructural Evolution of 6082 Aluminum Alloy with Different Heat Treatment Methods

Effect of Post-Aging on Microstructure and Mechanical Properties of an Ultrafine-Grained 6061 Aluminum Alloy

Revealing the Extra Strengthening and Strain Hardening of Dissimilar Age-Strengthened Al Alloy Laminates

Stress Relaxation Aging Behavior and Constitutive Modelling of AA7150-T7751 under Different Temperatures, Initial Stress Levels and Pre-Strains