Abstract:One of the important failure criteria of press operations in industry for forming simulations is the Forming Limit Diagram (FLD). The complex loading effects on FLD, in particular the localized necking phenomenon under stretch-bending condition, have not been fully investigated and well understood. In practical sheet metal applications, the deformation is invariably three dimensional with a combination of stretching and bending. For most sheet materials under these complex loading processes used in industry, strong Bauschinger effect is observed, and the material hardening behavior tends to be anisotropic. This study aims to understand and evaluate such anisotropic hardening effect on the forming limit prediction under stretch-bending condition. The extended through-thickness Marciniak–Kuczynski (M–K) analysis is incorporated with Yoshida–Uemori (YU) two-surface kinematic hardening constitutive model, which has a more accurate description of the reverse loading behavior than that of the conventional isotropic hardening model. The material parameters used in this paper for YU model are calibrated with the experimental data from uniaxial large-strain tension-compression cyclic test. Both the isotropic hardening and YU kinematic hardening models with Hill'48 yield surface are employed in the analysis for the purpose of comparison. The Forming Limit Average Stress Diagram (FLASD) under stretch-bending condition is proposed to extend the understanding of Forming Limit Stress Diagram (FLSD) from in-plane to out-of-plane deformations. The “bending-ratio-dependent” phenomenon in forming limit diagram is predicted and observed in both stress/strain space with the proposed method. It suggests that the individual stress/strain state cannot represent system behavior. Forming limits under stretch-bending is suggested as an occurrence of system instability, not individual material instability. The system behavior of sheet metal deformation is reinforced as critical to the understanding of necking instability in stretch bending processes. The analysis shows that the Bauschinger effect provides positive effect in delaying the necking instability, predicting higher formability for sheet metals under stretch-bending. The insight obtained in this paper provides further understanding of the localized necking phenomenon under stretch-bending condition.

Strain hardening in bent copper foils

Bending Stress Relaxation of Microscale Single-Crystal Copper at Room Temperature: an in Situ SEM Study

Analysis of Microbending of CuZn37 Brass Foils Based on Strain Gradient Hardening Models

Micro-bending of Metallic Crystalline Foils by Non-Local Dislocation Density Based Crystal Plasticity Finite Element Model

Mechanical and microstructural single-crystal Bauschinger effects: Observation of reversible plasticity in copper during bending

Effect of Alternating Bending on the Structure and Mechanical Properties of Tough-Pitch Copper

Mechanical Behaviour and the Evolution of the Dislocation Structure of Copper Polycrystal Deformed under Fatigue–tension and Tension–fatigue Sequential Strain Paths

Determination of Material Intrinsic Length and Strain Gradient Hardening in Microbending Process

The Strain Hardening of Micro-Sized Face-Centered-cubic Single Crystal Metals: A Crystal Plasticity Study

A fundamental understanding of how dislocation densities affect strain hardening behavior in copper single crystalline micropillars

Strengthening Versus Softening Of Nanotwinned Copper Depending On Prestress And Twin Spacing

Cyclic Stress-Strain Response Of A Copper Tricrystal And Bicrystal

Elastic size effect of single crystal copper beams under combined loading of torsion and bending

Micro-cantilever bending tests for understanding size effect in gradient elasticity

Experimental and numerical investigation of combined isotropic-kinematic hardening behavior of sheet metals

Strain Hardening and Large Tensile Elongation in Ultrahigh-Strength Nano-Twinned Copper

Influence of Crystal Structure on Size Dependent Deformation Behavior and Strain Heterogeneity in Micro-Scale Deformation

Processing and Specimen Thickness to Grain Size (t/d) Ratio Effects on Tensile Behaviour and Microformability of Copper Foils

Simulation of Scale Dependency on Tensile Mechanical Properties of Single Crystal Copper Nano-Rod

Sheet metal forming limits under stretch-bending with anisotropic hardening

Interactive Effects of Microstructure and Interface on Tensile Deformation Behaviors of Cu/Ni Clad Foils