Abstract:The effects of hole shape and orientation on the mechanical properties of micro-scale 2D honeycomb structures, fabricated using a focused ion beam equipment, have been investigated using an in situ micro-mechanical testing machine inside the scanning electron microscope . The material used was single-crystal Ni oriented in the direction, with the plane of the 2D micro-lattice having a {001} normal direction. The hole shapes explored were hexagonal and circular, while two different orientations of the hexagonal holes were also compared. One of these orientations had a horizontal arm (designated 0° orientation), while the other had a vertical arm (30° orientation) in each hexagon. The results indicate that there is substantial change in strength and ductility depending on the orientation and shape of the holes with respect to the tensile axis. The samples with 30° oriented hexagonal holes had the lowest strength and highest ductility, while the samples with circular holes showed the greatest yield and tensile strength. The samples with the 0° orientated hexagonal holes had much higher strength and lower ductility than the 30° orientated ones. Moreover, the samples with 0° orientated hexagonal holes, which had a similar hole pattern arrangement to the ones with circular holes, had a similar strength to those of the latter type. Thus, it is apparent from this study that the orientation or arrangement of the holes is more important in determining the properties of the 2D microlattice than the shape of the holes. Finite element simulation of the lattice structures utilised the GTN (Gurson, Tvergaard and Needleman) model to evaluate the failure modes under uniaxial tension. The lattice structure has been shown, in a previous paper by the authors, to exhibit composite like behaviour with strength differences in various parts arising from size effects. These size effect variations were incorporated into the model, and a generalised formulation for the GTN parameters was proposed on the basis of one of the experimental configurations and subsequently applied to the other geometries. The models were in good quantitative agreement with the experimental results with accurate representation of the flows stress and failure modes.

Crystal plasticity finite element study of tension-induced anisotropic contraction of additively manufactured Haynes 282

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Crystal Plasticity Modeling and Neutron Diffraction Measurements of a Magnesium AZ31B Plate: Effects of Plastic Anisotropy and Surrounding Grains

High Strain Gradient Plasticity Associated with Wedge Indentation into Face-Centered Cubic Single Crystals: Geometrically Necessary Dislocation Densities

Crystal Plasticity Quantification of Anisotropic Tensile and Fatigue Properties in Laser Powder Bed Fused Inconel 718 Superalloy

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

An analysis of nonuniform and localized deformation in ductile single crystals

Crystal plasticity modeling of non-Schmid yield behavior: from Ni3Al single crystals to Ni-based superalloys

Investigation of the grain deformation to orthogonal cutting process of the textured Alloy 718 fabricated by laser powder bed fusion

Deformation behaviour of hexagonal- and circular-patterned Ni single-crystal 2D micro-lattices via in situ micro-tensile testing and computational analysis

Plastic deformations and strain hardening in fully dense granular crystals

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

3D microstructural and strain evolution during the early stages of tensile deformation

On the Evolution of Lattice Deformation in Austenitic Stainless Steels—the Role of Work Hardening at Finite Strains

Anomalous plasticity of body-centered-cubic crystals with non-Schmid effect

A Large Deformation Atomistic Study Examining Crystal Orientation Effects on the Stress–strain Relationship

Study of Fcc Metal Tension Behaviour by Crystal Plasticity Finite Element Method

Molecular Dynamics Simulations of Orientation Effects During Tension, Compression, and Bending Deformations of Magnesium Nanocrystals

Crystal Plasticity Finite Element Simulations for Single Phase Titanium Alloys: Effect of Polycrystalline Aggregate Features on the Mechanical Response

Crystal Plasticity Behavior of Single-Crystal Pure Magnesium under Plane-Strain Compression

Effect of microstructure on fatigue crack propagation in additive manufactured nickel-based superalloy Haynes 282: an experiment and crystal plasticity study