Abstract:The nucleation of crystals is a highly non-homogeneous process. It depends on the number of nucleation sites, the rate of cooling, initial imperfections in the molten liquid and other variables. These inhomogeneities not only vary from location to location but they give rise to non-uniform residual stresses throughout the solid. The existence of initial microcracks and dislocations in a polycrystal is the rule rather than the exception. Knowledge of the micro-dislocational initial defects can be important since they can affect the ensuing service stress and strain states, particularly when the size of the system is in microns. The objective of this work is to develop a micro-atomic multiscale damage model for estimating the initial damage during processing of the material. In what follows, an effective analytical solution will be found for the specific case of a microcrack generating edge dislocations under in-plane shear loading. Cross-scale characteristics will be determined although discontinuities cannot be avoided if equilibrium mechanics theories are to be used for the range of microscopic and atomic scales. The unique idea of a "scale multiplier" is used to connect the microcrack and edge dislocations. The transition from microscopic to atomic can be smoothed out by introducing additional meso zones that would further divide the scale ranges into smaller segments. The process involves labor. Since it will not entail new physical insights, elaboration will not be made until the effort can be justified by the need. It is more important to illustrate the method for treating multiscale damage. Numerical results are obtained and displayed graphically for quantities of interest. The sliding displacement attains its maximum value at the end of the segment where a uniform residual stress is assumed to prevail. Edge dislocations are therefore generated. And they reach a maximum at a distance of about one third of the length of the segment from the point at which residual stresses are locked into the system. The location of this peak shifts with the magnitude of the residual stress. The decay and cross scaling effects of the strain energy density functions are also exhibited. They are relevant for discussing potential failure. In addition, these findings are expected to alter if the residual stresses are non-uniform. Such situations will depend on the specific application. The exact shapes of the microcrack and edge dislocation are depicted figuratively; they are not the important issues. Their singular characteristics, represented by the 1/r(0.5) and 1/r, however, are essential to show the difference in strength of local intensification with r being the distance from the singular points. The relevant quantities are the energy level and characteristic length associated with the micro-defect or crack and the atomic-defect or dislocation. Hence, there is no loss in generality from using the line crack-edge dislocation model for considering the effect of residual stresses. Since the corresponding problem for generating screw dislocation has already been considered in previous work, the addition of edge dislocations can be used to generate a more general solution of line dislocations in a plane under the combined effects of in-plane and out-of-plane shear action. Even though this work considers only the case of uniform residual stress trapped ahead of a microcrack, other situations of non-uniform residual stresses can be obtained by superposition.

An analysis of nonuniform and localized deformation in ductile single crystals

Geometrical effects in the inhomogeneous deformation of ductile single crystals

The inhomogeneity of plastic deformation in ductile single crystals

Cylindrical Void in a Rigid-Ideally Plastic Single Crystal. Part I: Anisotropic Slip Line Theory Solution for Face-Centered Cubic Crystals

Anisotropic Damage Model under Continuum Slip Crystal Plasticity Theory for Single Crystals

Cylindrical void in a rigid-ideally plastic single crystal III: Hexagonal close-packed crystal

On the yielding of a defect-rich model crystal under shear: insights from molecular dynamics simulations

Non-uniform Stress Field and Stress Concentration Induced by Grain Boundary and Triple Junction of Tricrystal

Modeling the Rate-Dependent Ductile-Brittle Transition in Amorphous Polymers

A continuum description of nonlinear elasticity, slip and twinning, with application to sapphire

A Reduced Micromorphic Single Crystal Plasticity Model at Finite Deformations. Application to Strain Localization and Void Growth in Ductile Metals

On the numerical treatment and analysis of finite deformation ductile single crystal plasticity

Semi-brittle flow of rocks: Cracks, dislocations and strain hardening

Cleavage crack formation and the effect of the structure of the nucleating deformation process

On the Evolution of Lattice Deformation in Austenitic Stainless Steels—the Role of Work Hardening at Finite Strains

Path Dependency of Plastic Deformation in Crystals: Work Hardening, Crystallographic Rotation and Dislocation Structure Evolution

Mechanical Aspects of Nonhomogeneous Deformation of Aluminum Single Crystals under Compression along [100] and [110] Directions

Intrinsic Instability and Nonuniformity of Plastic Deformation

Strain localization and shear banding in ductile materials

Length Scale Effects on the Geometric Softening of Precipitated Single Crystals

A micromechanical cracking imperfection model of edge dislocations generated by residual stresses