Abstract:In contrast to austenitic and martensitic stainless steels, ferritic stainless steels have a lower hardness and wear resistance but exhibit excellent corrosion resistance. Due to this fact, their use in the aerospace, automobile, and house construction industries is restricted. Several methods have been utilized to enhance the tribological characteristics of ferritic stainless steels. In this work, titanium nitride coating has been carried out by using a cathodic cage of titanium material, and later on, the titanium cathodic cage is replaced by an AISI-304 cathodic cage in a CCPN chamber to form iron nitride coating on AISI-430 ferritic stainless steel coupons through a plasma nitriding process for 4 h at a fixed temperature of 400 °C. The microstructures and mechanical traits of all processed and control coupons were analyzed using scanning electron microscopy, X-ray diffraction, ball-on-disc wear tester, and microhardness tester techniques. The results showed that hardness increased up to 1489 HV with the titanium cage, which is much higher than the hardness of the base material (270 HV). The titanium cage-treated coupons have high layer thickness, smooth surface morphology, and a minimum crystallite size of 2.2 nm. The wear rate was reduced up to 50% over the base material after the titanium cage plasma treatment. The base coupon exhibited severe abrasive wear, whereas nitrided coupons exhibited dominant adhesive wear. In the iron nitride coatings, this effect is also important, owing to the more influential cleaning process in a glow discharge, and the better adhesion with enhanced interlayer thickness is attributed to the fact that the compliance of the interlayer minimizes shear stresses at the coating-substrate interface. The use of a graded interface improves adhesion compared with the case where no interlayer is used but a titanium interlayer of comparable thickness provides a significant increase in measured adhesion. For both titanium and iron nitride films, there is a reduction in wear volume which is a function of interlayer thickness; this will have a substantial effect on wear lifetime. Thus by careful control of the interlayer thickness and composition, it should be possible to improve coating performance in tribological applications.

Surface Analysis of AISI D2 Steel Treated by Plasma Nitriding and Niobium and Vanadium Nitride Films by Cathodic Cage Plasma Deposition

Study of the Properties of Iron and Vanadium Nitride Coatings by CCPD on 1080 Steel

Surface modification of AISI-420 steel by cathodic cage plasma niobium nitride deposition

Influence of Time and Temperature of Plasma Nitriding on the Wear Resistance of Ni–Cr–Mo‐Based Films Deposited by AISI 904L Cathodic Cage on SAE 6160 Steel

Effect of Pre-treatment and Duration of Pulse Plasma Nitriding on Duplex Plasma Treatment by Physical Vapor Deposition of TiN on AISI D2 Steel

Surface integrity of machined AISI D2 steel and its effect on the adhesion of a PVD-AlCrN coating

Evaluation of titanium nitride/titanium aluminum nitride thin film coating, plasma nitriding on AISI 304 stainless steel using the plasma-assisted physical vapor deposition process, and thermal stress investigated through finite-element analysis

Plasma Nitriding of AISI 304 Stainless Steel in Cathodic and Floating Electric Potential: Influence on Morphology, Chemical Characteristics and Tribological Behavior

Improved wear resistance of AISI-4340 steel by Ti–Nb–C–N and MoS 2 composite coating by cathodic cage plasma deposition

Study of the Role of Titanium and Iron Cathodic Cages on Plasma-Nitrided AISI 430 Ferritic Stainless Steel

Plasma Deposition of Ti-Nb-N Films on AISI 304 Stainless Steel by Cathodic Cage Technique

Diamond-Like Carbon Coatings on Plasma Nitrided M2 Steel: effect of deposition parameters on adhesion properties

Novel Performances of in Situ Plasma Nitriding-Pvd Duplex-Treated Nanocrystalline TiN Coatings

Surface modification of high-speed steel (HSS) drills by plasma nitriding and cathodic cage tin deposition

Characterization of Tribological and Mechanical Properties of the Si3N4 Coating Fabricated by Duplex Surface Treatment of Pack Siliconizing and Plasma Nitriding on AISI D2 Tool Steel

V STAINLESS STEEL PROPERTY IMPROVEMENT BY ION NITRIDING AND NITROCARBURIZING

High Temperature Plasma Nitriding to Modify Ti Coated C17200 Cu Surface: Microstructure and Tribological Properties

Graded and Single-Layer NiAl/WC-Co Coatings Processed by Plasma Transferred Arc Directed Energy Deposition

TiNbN Hard Coating Deposited at Varied Substrate Temperature by Cathodic Arc: Tribological Performance under Simulated Cutting Conditions

Microstructure, Adhesion and Tribological Properties of CrN/CrTiAlSiN/WCrTiAlN Multilayer Coatings Deposited on Nitrocarburized AISI 4140 Steel

Effect Of Hybrid Surface Treatment Composed Of Plasma Nitriding And W-Cr-Ti-Al-N Coating On Tribological Behavior Of Aisi 316l Steel