Abstract:In contrast to austenitic and martensitic stainless steels, ferritic stainless steels have a lower hardness and wear resistance but exhibit excellent corrosion resistance. Due to this fact, their use in the aerospace, automobile, and house construction industries is restricted. Several methods have been utilized to enhance the tribological characteristics of ferritic stainless steels. In this work, titanium nitride coating has been carried out by using a cathodic cage of titanium material, and later on, the titanium cathodic cage is replaced by an AISI-304 cathodic cage in a CCPN chamber to form iron nitride coating on AISI-430 ferritic stainless steel coupons through a plasma nitriding process for 4 h at a fixed temperature of 400 °C. The microstructures and mechanical traits of all processed and control coupons were analyzed using scanning electron microscopy, X-ray diffraction, ball-on-disc wear tester, and microhardness tester techniques. The results showed that hardness increased up to 1489 HV with the titanium cage, which is much higher than the hardness of the base material (270 HV). The titanium cage-treated coupons have high layer thickness, smooth surface morphology, and a minimum crystallite size of 2.2 nm. The wear rate was reduced up to 50% over the base material after the titanium cage plasma treatment. The base coupon exhibited severe abrasive wear, whereas nitrided coupons exhibited dominant adhesive wear. In the iron nitride coatings, this effect is also important, owing to the more influential cleaning process in a glow discharge, and the better adhesion with enhanced interlayer thickness is attributed to the fact that the compliance of the interlayer minimizes shear stresses at the coating-substrate interface. The use of a graded interface improves adhesion compared with the case where no interlayer is used but a titanium interlayer of comparable thickness provides a significant increase in measured adhesion. For both titanium and iron nitride films, there is a reduction in wear volume which is a function of interlayer thickness; this will have a substantial effect on wear lifetime. Thus by careful control of the interlayer thickness and composition, it should be possible to improve coating performance in tribological applications.

Evaluation of titanium nitride/titanium aluminum nitride thin film coating, plasma nitriding on AISI 304 stainless steel using the plasma-assisted physical vapor deposition process, and thermal stress investigated through finite-element analysis

Study of optical and electrical properties of TiN thin films prepared by cathodic ion sputtering

Mechanical properties of TiN thin film coatings on 304 stainless steel substrates

Study of the Role of Titanium and Iron Cathodic Cages on Plasma-Nitrided AISI 430 Ferritic Stainless Steel

Adhesion and growth of titanium nitride coating deposited on AISI 316L using cylindrical magnetron sputtering

Deposition of TiN and TiAlN Thin Films on Stainless Steel Tubes by a Cylindrical Magnetron Sputtering Method

Tribological Investigation of W-Ti-N Thin Film on Plasma Nitrided Stainless-Steel Multilayer Coating

Properties of Titanium Nitride Fabricated on Stainless Steel by Plasma-Based Ion Implantation/Deposition

Characterization of TiN, TiC and TiCN coatings on Ti–50.6 at.% Ni alloy deposited by PIII and deposition technique

Plasma Nitriding of AISI 304 Stainless Steel in Cathodic and Floating Electric Potential: Influence on Morphology, Chemical Characteristics and Tribological Behavior

Effect Of Hybrid Surface Treatment Composed Of Plasma Nitriding And W-Cr-Ti-Al-N Coating On Tribological Behavior Of Aisi 316l Steel

Metallurgical, erosion, and sensitization performance of TiAlN monolayer and TiAlN/TiN multilayer ceramic coatings on AISI 304 boiler steel

Mechanical Properties Evaluation and Parametric Optimization of Atmospheric Plasma Spray NiTi Coating

Microstructural response and wear behaviour of Ti-6Al-4V impregnated with Ni/Al2O3 + TiO2 nanostructured coating using an electric arc

Plasma Deposition of Ti-Nb-N Films on AISI 304 Stainless Steel by Cathodic Cage Technique

Effects of titanium nitride coatings on surface and corrosion characteristics of Ni-Ti alloy

Surface Characterization and Electrochemical Studies of Biomedical Niti Alloy Coated with Tin by Piiid

Fabrication and Characterization of In-Situ Duplex Plasma-Treated Nanocrystalline Ti/AlTiN Coatings

Modification mechanism of Ti-6Al-4V alloy with pre-coated Ti-Cu-Al multilayer film treated by ion nitriding: Experiments and first-principles calculations

Effect of AISI H13 Steel Substrate Nitriding on AlCrN, ZrN, TiSiN, and TiCrN Multilayer PVD Coatings Wear and Friction Behaviors at a Different Temperature Level