Abstract:Cu2MgFe thermoelectric interface material (TEiM) is designed, following a general strategy, i.e., considering high bonding propensity, thermal expansion matching, diffusion passivation, and dopant inactivation. The Mg2Sn0.75Ge0.25 TE device exhibits a high‐power density of 2.6 W cm−2 and a conversion efficiency of 8% under a temperature difference of 370 °C. The TEiM design strategy bridges high‐performance TE materials and devices. Electrode contact interfaces for practical thermoelectric (TE) devices require high bonding strength, low specific contact resistivity, and superb stability. Herein, the state‐of‐the‐art Cu2MgFe/Mg2Sn0.75Ge0.25 interface is designed for Mg2Sn0.75Ge0.25‐based TE devices, adhering to the general strategy of high bonding propensity, thermal expansion matching, diffusion passivation, and dopant inactivation. The interfacial stability is verified by the in situ transmission electron microscopy analysis, thereby confirming the contributions from decreasing the chemical potential gradient and increasing the diffusion activation energy barrier. The single‐leg device exhibits a high power density (ωmax) of 2.6 W cm−2 and conversion efficiency (ηmax) of 8% under a temperature difference (ΔT) of 370 °C, which is the record‐breaking value in comparison to other Mg2(Si, Ge, Sn)‐based TE devices. Additionally, a two‐couple device with p‐type Bi2Te3 shows an excellent ωmax of 1.3 W cm−2 and ηmax of 5.4% under a ΔT of 270 °C, comparable to commercial Bi2Te3 devices. The proposed interface design strategy provides a general technique for constructing high‐performance devices using cutting‐edge TE materials.

Miniaturized in-plane π-type thermoelectric device composed of a II–IV semiconductor thin film prepared by microfabrication

n-type thermoelectric material Mg2Sn0.75Ge0.25 for high power generation

Microfabrication of thermoelectric materials by silicon molding process

Development of Thermoelectric Microdevices by Combining Materials Processing and Silicon Micromachining Technology

A new type of micro-thermoelectric power generator fabricated by nanowire array thermoelectric material

High Thermoelectric Performance of Bi-Doped Mg 2 Si 0.4 Sn 0.6 and Mg 2 Si 0.6 Sn 0.4 based on Recyclable Si Kerf Derived from PV Manufacturing

High Figures Of Merit And Natural Nanostructures In Mg2si0.4sn0.6 Based Thermoelectric Materials

Interface Engineering Boosting High Power Density and Conversion Efficiency in Mg2Sn0.75Ge0.25‐Based Thermoelectric Devices

Manufacturing thermoelectric micro modules using micromachined silicon wafers

Development of MEMS Process Compatible (Bi,Sb)2(Se,Te)3-Based Thin Films for Scalable Fabrication of Planar Micro-Thermoelectric Generators

Heavily Boron-Doped Silicon Layer for the Fabrication of Nanoscale Thermoelectric Devices

Fabrication And Evaluation Of Microscale Thermoelectric Modules Of Bi2te3-Based Alloys

Simple Synthesis and Thermoelectric Properties of Mg2 + xSi0.5Sn0.5Sb0.075 Materials with Heterogeneous Microstructure

Planar-type SiGe thermoelectric generator with double cavity structure

Maximizing the performance of n-type Mg3Bi2 based materials for room-temperature power generation and thermoelectric cooling

Energy Conversion Using New Thermoelectric Generator

A High Power Density Micro-Thermoelectric Generator Fabricated by an Integrated Bottom-Up Approach

Fabrication and evaluation of microscale thermoelectric modules of Bi<sub>2</sub>Te<sub>3</sub>-based alloys

No external load measurement strategy for micro thermoelectric generator based on high-performance Si1−x−yGexSny film

High‐Performing Flexible Mg3Bi2 Thin‐Film Thermoelectrics

Enhanced Thermoelectric Performance of Mg-Sn Thin Films: Role of Mg9Sn5 Phase and One-Dimensional Electronic Structure