Abstract:The study proposes a computational and analytical model of finding the stress-strain state and force characteristics when crimping thin-walled pipe blanks in a curved axisymmetric matrix. The mathematical model is based on the equilibrium equation of the momentless theory of thin axisymmetric shells taking into account the nonlinear law of plasticity, changes in the wall thickness of the workpiece and contact friction. As a mathematical model of the material, a linear-power approximation of the deformation diagram of an elastic-plastic body is considered taking into account the compressibility of the material. The methodology for estimating the stress-strain state of the workpiece during crimping is constructed using a generalized formulation for an arbitrary curve forming the working contour of the matrix. The basis of the numerical calculation method was the method of variable elasticity parameters, which makes it possible to determine stresses and strains, the thickness distribution in the meridional section, the amount of contact pressure, and also to plot the change in the crimping force depending on the displacement of the point of application of the force relative to the matrix. The distribution of stresses and strains of a thin-walled billet made of aviation aluminum alloy during crimping is calculated using the example of a matrix, the working contour of which is described by a sinusoidal trigonometric function. During crimping, according to the results of the proposed numerical technique, a thickening of the blank wall is noted, as well as an increase in the deforming force when moving the point of application of the force. The proposed mathematical model can be used to calculate the process of crimping workpieces in axisymmetric matrices of complex shapes, with variable curvature, which is especially important in the field of aircraft engineering. The research results make it possible to consider changes in the workpiece’s thickness and physical nonlinearity in the field of plastic strain, when assessing the picture of the stress-strain state.

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. DETERMINATION OF KINEMATIC AND STRESS STATES

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. METHODS FOR CALCULATING THE TECHNOLOGICAL PARAMETERS OF EXTRUSION OF PRODUCTS WITH THE SAME RADII OF THE UPPER AND LOWER PARTS

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. ACTUALITY AND STATEMENT OF PROBLEM

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. EXPERIMENTAL VERIFICATION OF THEORETICAL FORMULAS DURING EXTRUSION WITH HARDENING OF STEELS 10, 12KH18N9T AND BRASS L63

COMPUTATIONAL AND EXPERIMENTAL STUDY OF THE STRESS-STRAIN STATE OF A PIPE UNDER EXTERNAL RADIAL LOAD, INTERNAL PRESSURE AND TEMPERATURE DIFFERENCE

COMBINED EXTRUSION OF GLASSES WITH A CONICAL BOTTOM. KINEMATIC AND STRESS STATES OF THE PLASTIC REGION IN CONTACT WITH THE CONICAL SURFACE OF THE MATRIX

Stress Evaluation in the Blank Critical Region During Extrusion of the Pipe Blank into the Hole

Calculation of radially inhomogeneous ring loaded with normal and tangential loads

Theoretical Assessment of Burst Failure of Internally Pressurized Defect-Free Pipelines with Plastic Anisotropy

MANUFACTURE INVESTIGATION OF CARTRIDGE WITH BOTTOM-MOST PART FLANGE BY DIRECT EXTRUSION WITH COUNTERPUNCH. REPORT 18. EXPERIMENTAL CHECK OF THEORETICAL RESULTS FOR DIFFERENT HOLLOW RADIUSES AND BOTTOM-MOST PART THICKNESSES

Burst Pressure of Pipelines with Plastic Anisotropy under Combined Internal and External Pressures

Theoretical studies of reverse extrusion of steel pipe by conical punch

STRESS-STRAIN STATE OF THIN-WALLED PIPE BLANKS DURING CRIMPING IN A CURVED AXISYMMETRIC MATRIX

SIMULATION OF MULTI-STAGE COLD FORMING OF A THIN-WALLED VESSEL

INFLUENCE OF VARIABLE YOUNG’S MODULUS ON RESIDUAL STRESSES INDUCED BY ROTATIONAL AUTOFRETTAGE OF A TUBE WITH FIXED ENDS

Numerical analysis of the stress-strain state of a polymer reinforced pipeline

Study of Chromium Steel Ductility During Pipe Extrusion

Stress analysis of double-walled pipes undergone mechanical drawing process

THEORETICAL COMPUTATION ON THE EXTRUSION OF LARGE SCALE STEEL PIPE BASED ON UPPER BOUND METHOD

RESEARCH OF STRENGTH OF CONTACT OF THE PLASTIC PIPE ANDCONCRETE WHEN CALCULATING PLASTIC PIPE CONCRETE STRUCTURES

Bending of sheets and profiles on a four-roll machine for rocket bodies, pipe and frame products. Part 13