Abstract:The article presents the results of the development and research of the combined technological process of forming the outer and inner flanges of the lids of fractional and distillation columns on sheet blanks by the method of stamping by rolling and rotary drawing. For this purpose, equipment has been developed that allows to form both outer and inner flanges of the blank in one run of the conical roll. Studies have shown that technological capabilities of the process are limited by the risk of destruction of the top layers of the outer flange bending center and its corrugation, as well as by the neck formation or destruction of the peripheral areas of the inner flange. To assess the deformability of the outer flange, the stress-strain state of its bending center was investigated. According to the set stress values, the stress state of the material is determined, the maximum value of which on the surface of the bending zone is Formula for determining the minimum radius of the mandrel, which when using the values of the critical ductility of the material allows to prevent destruction. As well, an expression for determining the maximum width of the flange, provided that the destruction of peripheral areas is prevented, is obtained. As corrugations formation is the main danger in forming the external flanges by the stamping by rolling method (SR), the expression for determining the maximum width of the flange under the condition of a stable process is obtained. If it is necessary to get more developed flanges, it is proposed to provide thinning of their walls by rotary extraction at the second stage. When forming the inner flanges of the blank stacks radial compressive stresses and tangential tensile stresses in the material are brought about. The action of tangential stresses causes loss of stability of the flange by way of neck formation. The value of the critical strains increases with the approach to the state of plain-strain deformation. Therefore, it is recommended to develop process parameters based on construction of the critical strains diagrams.

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. METHODS FOR CALCULATING THE TECHNOLOGICAL PARAMETERS OF EXTRUSION OF PRODUCTS WITH THE SAME RADII OF THE UPPER AND LOWER PARTS

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. ACTUALITY AND STATEMENT OF PROBLEM

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. EXPERIMENTAL VERIFICATION OF THEORETICAL FORMULAS DURING EXTRUSION WITH HARDENING OF STEELS 10, 12KH18N9T AND BRASS L63

RADIAL EXTRUSION OF A PIPE BILLET WITH INTERNAL LEDGE. DETERMINATION OF KINEMATIC AND STRESS STATES

Theoretical studies of reverse extrusion of steel pipe by conical punch

Optimization of the Processes of Forming and Welding of Large-Diameter Pipes with the Help of Mathematic Simulation

MANUFACTURE INVESTIGATION OF CARTRIDGE WITH BOTTOM-MOST PART FLANGE BY DIRECT EXTRUSION WITH COUNTERPUNCH. REPORT 18. EXPERIMENTAL CHECK OF THEORETICAL RESULTS FOR DIFFERENT HOLLOW RADIUSES AND BOTTOM-MOST PART THICKNESSES

Ultimate Strength Evaluation of the Multistage Technological Process of Cold Sheet Stamping Technique for Manufacture of Thin-Walled Vessels

SIMULATION OF MULTI-STAGE COLD FORMING OF A THIN-WALLED VESSEL

Bending of sheets and profiles on a four-roll machine for rocket bodies, pipe and frame products. Part 13

TECHNOLOGICAL PASSPORT STUDY PISTON AND CONNECTING ROD BARE MATERIAL AXIAL ROTARY PISTON PUMP

DEVELOPMENT OF THE COMBINED TECHNOLOGICAL PROCESS OF BLANK STACKS FLANGES FORMATION BY THE METHOD OF STAMPING BY ROLLING AND ROTARY DRAWING

Development of the Technology of Manufacturing Aerospace Composite Tubular Elements by Radial Braiding

THEORETICAL COMPUTATION ON THE EXTRUSION OF LARGE SCALE STEEL PIPE BASED ON UPPER BOUND METHOD

Hot Radial Upset-Extruding Process for Tube Structure with a Nozzle of 316LN Stainless Steel

COMPUTATIONAL AND EXPERIMENTAL STUDY OF THE STRESS-STRAIN STATE OF A PIPE UNDER EXTERNAL RADIAL LOAD, INTERNAL PRESSURE AND TEMPERATURE DIFFERENCE

Theoretical and Experimental Study on the Effect of Selected Parameters in a New Method of Extrusion with a Movable Sleeve

Comprehensive assessment of the production of a pipe billet with a flange by forging at various temperature conditions

Development of the method for determining the deformation parameters and remidal stresses of metal in the manufacture of straight-seached pipes of large diameter using expansion

Axial Rotary Forging of Inner Flanges at Thin Wall Tube Blanks

Technology Optimization Analysis of Three-Roll Rotary Piercing Process for Seamless Steel Pipe