Abstract:A series of polyethylene (PE) blends consisting of a linear high density polyethylene (HDPE) and a linear low density polyethylene (LLDPE) with an octane-chain branch density of 120/1000 carbon was prepared at different concentrations. The two components of this set of blends possessed isorefractive indices, thus, making it difficult to detect their liquid–liquid phase separation via scattering techniques. Above the experimentally observed melting temperature of HDPE, Tm = 133 °C, this series of blends can be considered to be in the liquid state. The LLDPE crystallization temperature was below 50 °C; therefore, above 80 °C and below the melting temperature of HDPE, a series of crystalline–amorphous PE blends could be created. A specifically designed two-step isothermal experimental procedure was utilized to monitor the liquid–liquid phase separation of this set of blends. The first step was to quench the system from temperatures of known miscibility and isothermally anneal them at a temperature higher than the equilibrium melting temperature of the HDPE for the purpose of allowing the phase morphology to develop from liquid–liquid phase separation. The second step was to quench the system to a temperature at which the HDPE could rapidly crystallize. The time for developing 50% of the total crystallinity (t1/2) was used to monitor the crystallization kinetics. Because phase separation results in HDPE-rich domains where the crystallization rates are increased, this technique provided an experimental measure to identify the binodal curve of the liquid–liquid phase separation for the system indicated by faster t1/2. The annealing temperature in the first step that exhibits an onset of the decrease in t1/2 is the temperature of the binodal point for that blend composition. In addition, the HDPE-rich domains crystallized to form spherulites which decorate the phase-separated morphology. Therefore, the crystal dispersion indicates whether the phase separation followed a nucleation-and-growth process or a spinodal decomposition process. These crystal-decorated morphologies enabled the spinodal curve to be experimentally determined for the first time in this set of blends.

Calibration curve establishment and fractionation temperature selection of polyethylene for preparative temperature rising elution fractionation

Application of Temperature Rising Elution Fractionation in Polyolefins

Preparative temperature rising elution fractionation of polyolefin elastomer and its chain microstructure

Temperature rising elution fractionation of polypropylene produced by heterogeneous Ziegler-Natta catalysts

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Characterization of Intramolecular Composition Heterogeneity of Metallocene-Based and Conventional Ethylene-Butene Copolymers Using Tref/Dsc

Chain Structure and Mechanical Properties of Ethylene Copolymers in Two Operating Modes of Fluidized Bed Polymerization Reactor

Temperature Rising Elution Fractionation of Polypropylenes Produced by Heterogeneous Ziegler-Natta Catalysts Containing Different Internal Donors

Application of Crystal Fractionation Technology in the Research of Short-chain Branched Polyethylene

Temperature Rising Elution Fractionation of Syndiotactic Polypropylene Prepared by Homogeneous and Supported Metallocene Catalysts

Enhanced characterization of the chemical structure of high-density polyethylene by size exclusion/thermal fractionation on poly(styrene-co-divinylbenzene) columns

Separation and identification of ethylene-propylene block copolymer

Nonisothermal Crystallization of S-Pp Fractions

Nonisothermal Crystallization Kinetics of Ethylene-Butene Copolymer/Low-Density Polyethylene Blends

Probing Liquid‐Liquid Phase Separation of a Polyethylene Blend with Thermal Analysis

Isothermal thickening and thinning processes in low molecular weight poly(ethylene oxide) fractions crystallized from the melt - Effects of molecular configurational defects on crystallization, melting, and annealing

Temperature rising elution fractionation of PP/PE alloy and thermal behavior of the fractions

Liquid–liquid Phase Separation in a Polyethylene Blend Monitored by Crystallization Kinetics and Crystal-Decorated Phase Morphologies

Study on thermal behavior of impact polypropylene copolymer and its fractions

Preparation of Ethylene Chlorotrifluoroethylene Co-polymer Membranes Via Thermally Induced Phase Separation

Sensitive phase separation behavior of ultra-high molecular weight polyethylene in polybutene