Abstract:Diphenyl carbonate (DPC) and diphenyl ketone (DPK) were used as diluents to prepare microporous polyvinylidene fluoride (PVDF) membranes via thermally induced phase-separation (TIPS) method. The liquid - liquid phase-separation phenomena were found in PVDF/DPC and PVDF/DPK systems during the thermally induced phase-separation processes. The monotectic points of PVDF/DPC and PVDF/DPK systems appeared at PVDF concentration approximately 30 and 56 %(wt), respectively. This suggested that PVDF membrane with a bicontinuous or cellular structure could be obtained when the PVDF concentration was less than the point values. The effects of polymer concentration and quenching temperature on the membrane structure, porosity, and tensile strength were also investigated. The results showed that low polymer concentration and high quenching temperature led to a large pore size membrane. The tensile strength of the membrane increased with the increase of the polymer concentration, but the porosity of the membrane decreased. On condition that the PVDF concentration was higher than monotectic points, only polymer crystallization occurred and a typical compact spherulitic structures were obtained. Moreover, a binary diluent of DPK and secondary solvent such as 1,2-propylene glycol (PG) was used to replace the single diluent in TIPS process. The phase diagram for the PVDF/binary diluent of DPK and PG system was measured in the range of the PG/DPK mass ratio changing from 0 to 2/3. Then the effects of the PG/DPK mass ratio and the PVDF concentration on membrane cross-section structures and tensile strength were also investigated. The results showed that the addition of PG brought about a shift of the cloud point curve to a higher temperature and the extension of the liquid-liquid phase separation region to a higher polymer concentration. Therefore a bicontinuous cross-section structure was obtained when the PG/DPK mass ratio was 3/7 and the polymer concentration was 30 wt%. As an increase of the PG/DPK mass ratio, the tensile strength increased gradually at a fixed PVDF concentration. Moreover, for the same PG/DPK mass ratio, the cross-section microstructure changed from a bicontinuous or a cellular structure to a spherulitic structure, and the tensile strength increased drastically as the polymer concentration increased from 20 wt% to 50 wt%. According to the properties of diluents, the industrial scale production line with a twin-screw extruder of microporous PVDF hollow fiber membranes was established and a series of different type hollow fiber membranes were prepared for the corresponding applications of pressure-driven modulus, submersed modulus and membrane bio-reactor modulus. At the same time, the full recycle of diluents was almostly actualized by using a series of unit opertaions such as extraction, distillation, delamination, sedimentation and drying processes. It means there is no waste emission in the preparation of PVDF membranes or it is a green process.

Preparation of Ethylene Chlorotrifluoroethylene Co-polymer Membranes Via Thermally Induced Phase Separation

ECTFE Membranes Prepared Via Thermally Induced Phase Separation —selection of Mixed Diluent

Preparation of Porous PVDF Membrane Via Thermally Induced Phase Separation with Diluent Mixture of DBP and DEHP

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Preparation of porous PVdF membrane via thermally induced phase separation using sulfolane

Preparation, Modification, and Application of Ethylene-Chlorotrifluoroethylene Copolymer Membranes

Preparation of Microporous Ultra High Molecular Weight Polyethylene (uhmwpe) by Thermally Induced Phase Separation of A Uhmwpe/Liquid Paraffin Mixture

Preparation of Ectfe Membranes with Bicontinuous Structure Via Tips Method by A Binary Diluent

Phase Behavior of Polyetherimide/Benzophenone/Triethylene Glycol Ternary System and Its Application for the Preparation of Microporous Membranes

Formation of Hydrophilic Ethylene-Acrylic Acid Copolymer Microporous Membranes Via Thermally Induced Phase Separation

PVDF Membrane Formation Via Thermally Induced Phase Separation

Development of Polymer Microporous Membranes Via Thermally Induced Phase Separation

Thermally Induced Phase Separation of Poly(vinylidene Fluoride)/diluent Systems: Optical Microscope and Infrared Spectroscopy Studies

ECTFE Membrane Fabrication Via TIPS Method Using ATBC Diluent for Vacuum Membrane Distillation

Green preparation of polyvinylidene fluoride microfiltration membranes via thermally indueced phase separation method using diphenyl carbonate and diphenyl ketone as diluents

Preparation and Characterization of Cellulose Triacetate Membranes Via Thermally Induced Phase Separation

Preparation of PVDF Membranes via TIPS Method: The Effect of Mixed Diluents on Membrane Structure and Mechanical Property

Green thermally induced phase separation (TIPS) process for braided tube reinforced polyvinylidene fluoride (PVDF) hollow fiber composite membranes with favorable bonding layer

FORMATION OF LOW DENSITY POLYETHYLENE MICROPOROUS MEMBRANE VIA THERMALLY INDUCED PHASE SEPARATION--(Ⅱ) THE EFFECTS OF KINETIC FACTORS ON THE STRUCTURES OF MICROPOROUS MEMBRANES

Effect of cooling baths on EVOH microporous membrane structures in thermally induced phase separation

The Effect of Diluent Mixture with Upper Critical Solution Temperature on Membrane Formation Process, Microstructure, and Performance of PVDF Hollow Fiber Membrane by TIPS Process