Abstract:A series of polyethylene (PE) blends consisting of a linear high density polyethylene (HDPE) and a linear low density polyethylene (LLDPE) with an octane-chain branch density of 120/1000 carbon was prepared at different concentrations. The two components of this set of blends possessed isorefractive indices, thus, making it difficult to detect their liquid–liquid phase separation via scattering techniques. Above the experimentally observed melting temperature of HDPE, Tm = 133 °C, this series of blends can be considered to be in the liquid state. The LLDPE crystallization temperature was below 50 °C; therefore, above 80 °C and below the melting temperature of HDPE, a series of crystalline–amorphous PE blends could be created. A specifically designed two-step isothermal experimental procedure was utilized to monitor the liquid–liquid phase separation of this set of blends. The first step was to quench the system from temperatures of known miscibility and isothermally anneal them at a temperature higher than the equilibrium melting temperature of the HDPE for the purpose of allowing the phase morphology to develop from liquid–liquid phase separation. The second step was to quench the system to a temperature at which the HDPE could rapidly crystallize. The time for developing 50% of the total crystallinity (t1/2) was used to monitor the crystallization kinetics. Because phase separation results in HDPE-rich domains where the crystallization rates are increased, this technique provided an experimental measure to identify the binodal curve of the liquid–liquid phase separation for the system indicated by faster t1/2. The annealing temperature in the first step that exhibits an onset of the decrease in t1/2 is the temperature of the binodal point for that blend composition. In addition, the HDPE-rich domains crystallized to form spherulites which decorate the phase-separated morphology. Therefore, the crystal dispersion indicates whether the phase separation followed a nucleation-and-growth process or a spinodal decomposition process. These crystal-decorated morphologies enabled the spinodal curve to be experimentally determined for the first time in this set of blends.

Preparation of Microporous Ultra High Molecular Weight Polyethylene (uhmwpe) by Thermally Induced Phase Separation of A Uhmwpe/Liquid Paraffin Mixture

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Sensitive phase separation behavior of ultra-high molecular weight polyethylene in polybutene

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Phase separation and structure control in ultra-high molecular weight polyethylene microporous membrane

Morphology of porous UHMWPE originating from the S–L phase separation in UHMWPE/liquid paraffin (LP) blends

Preparation of Porous PVDF Membrane Via Thermally Induced Phase Separation with Diluent Mixture of DBP and DEHP

Hierarchical structure and properties of high‐density polyethylene (HDPE) microporous films fabricated via thermally‐induced phase separation (TIPS): Effect of presence of ultra‐high molecular weight polyethylene (UHMWPE)

Preparation and Properties of Ultra High Molecular Weight Polyethylene/High Density Polyethylene Microporous Membrane via Thermal Induced Phase Separation

Molecular Self-Assembly Assisted Liquid-Liquid Phase Separation In Ultrahigh Molecular Weight Polyethylene/Liquid Paraffin/Dibenzylidene Sorbitol Ternary Blends

Crystallization And Microporous Membrane Properties Of Ultrahigh Molecular Weight Polyethylene With Dibenzylidene Sorbitol

FORMATION OF LOW DENSITY POLYETHYLENE MICROPOROUS MEMBRANE VIA THERMALLY INDUCED PHASE SEPARATION--(Ⅱ) THE EFFECTS OF KINETIC FACTORS ON THE STRUCTURES OF MICROPOROUS MEMBRANES

Effect of Polypropylene Molecular Weight on Microporous Membrane Formation Via Thermally Induced Phase Separation

Probing Liquid‐Liquid Phase Separation of a Polyethylene Blend with Thermal Analysis

Tuning the water permeability of ultra-high molecular weight polyethylene microporous membrane by molecular self-assembly and flow field

Preparation and Characterization of PVDF Flat Sheet Microporous Membrane via Thermally Induced Phase Separation

Two-Phase Structure of Micro Ultrasonic Powder Molding Ultra-High Molecular Weight Polyethylene Parts

Development and evaluation of UHMWPE/woven fabric composite microfiltration membranes via thermally induced phase separation

Liquid–liquid Phase Separation in a Polyethylene Blend Monitored by Crystallization Kinetics and Crystal-Decorated Phase Morphologies

FORMATION OF LOW DENSITY POLYETHYLENE MICROPOROUS MEMBRANES VIA THERMALLY INDUCED PHASE SEPARATION--(Ⅰ) LDPE-18D/DPE SYSTEM

Preparation of PVDF-HFP Microporous Membranes via the Thermally Induced Phase Separation Process