Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

The Structurization of Aluminum Oxide Composite Ceramics Involving Products of Iron Oxide Reduction by Nanosized Nonstoichiometric Silicon Carbide

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Pressure Sintering, Structure and Some Properties of SiC–Al Composite Materials

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Nanostructured Composite Obtained by Mechanically Driven Reduction Reaction of Cuo and Al Powder Mixture

Effects of Composite Systems on Sintering Properties of Aluminum Oxide Ceramics

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Effect of CeO2 Content on Microstructure and Properties of SiCp/Al-Si Composites Prepared by Powder Metallurgy

Structure Investigation of Ball Milled Composite Powder Based on AlSi5Cu2 Alloy Chips Modified by Sic Particles

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

In-situ synthesis of Fe Si phases and their effects on the properties of SiC porous ceramics

Study of Microstructural and Mechanical Properties of Al/SiC/TiO2 Hybrid Nanocomposites Developed by Microwave Sintering

PROCESS AND MECHANISM OF MICROWAVE SINTERING OF SiC-Cu/Al COMPOSITES

Ultrafine Grained Bulk Ceramic Composites Consolidated from Nanostructured Composite Powders by Pressure Less Sintering

Sustainability in the Manufacturing of Eco-Friendly Aluminum Matrix Composite Materials

Properties and microstructure of machinable Al2O3/LaPO4 ceramic composites

Structural Evolutions and Oxidation Behavior of Fe-doped Silicon Oxycarbide Nanocomposites at Medium Temperatures

Effect of SiC Addition to Al2O3 Ceramics Used in Cutting Tools

Study of the Aid Effect of CuO-TiO2-Nb2O5 on the Dielectric and Structural Properties of Alumina Ceramics

Structural-Phase State and Properties of SiC Ceramics Obtained by Ultrasound-Assisted Liquid-Phase Sintering with Eutectic Additives