Abstract:High-energy ball milling represents an efficient process for producing composite powders consisting of ceramic particles dispersed in a metallic matrix. However, collision events, plastic deformations, and cold welding during the milling lead to a flake or block-like shape of the resulting composite powders. Further consolidation of such irregularly shaped powders by powder bed-based additive manufacturing technologies can be challenging because of their low flowability and low bulk density. In this work, different approaches, including milling process parameters (speed, process control agent atmosphere) and post-treatments (mechanical and thermal), are investigated on their suitability to influence the particle shape, especially concerning the roundness of the composite powders consisting of the aluminum alloy AlSi10Mg with 5 vol% SiC and Al2O3 reinforcement. It is found that milling with menthol as a process control agent leads to the finest composite powder compared to other milling parameters, with the lowest particle roundness of 0.39 (initial powders 0.84). No success in rounding the milled composite powder could be achieved through mechanical post-treatment in a planetary ball mill. On the other side, the thermal spraying of, e.g., SiC reinforced AlSi10Mg powder resulted in a 77–82% relative roundness. A remarkable change in the microstructure and the shape of the composite powders could also be observed after heat treatment in tube furnaces at a temperature above the melting point of AlSi10Mg. The best result in terms of improved roundness (relative to around 85%) was obtained for Al2O3 reinforced at 600 °C. A further increase of the temperature to 700 °C resulted in a moderate coarsening of powders with Al2O3 and extensive sintering of powders with SiC, presumably due to a different distribution inside the matrix.

Structure Investigation of Ball Milled Composite Powder Based on AlSi5Cu2 Alloy Chips Modified by Sic Particles

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

INFLUENCE OF MILLING TIME ON GROWTH MORPHOLOGY AND MECHANICAL PROPERTIES OF ALUMINUM-SILICON-CARBIDE COMPOSITES

Influencing the Size and Shape of High-Energy Ball Milled Particle Reinforced Aluminum Alloy Powder

Role of Different Fractions of Nano-size SiC and Milling Time on the Microstructure and Mechanical Properties of Al–SiC Nanocomposites

Fabrication of Ni/Sic Composite Powder by Mechanical Alloying and Its Effects on Properties of Copper Matrix Composites

Hot extrusion of SiCp/Al-Cu composites: optimizing mechanical properties through microstructural control

Preparation of SiCp/Al MMCs by Ball Milling and Stir Casting

Evaluating the morphology and distribution uniformity of AZ91D-SiC composite powder produced from magnesium chips by mechanical milling and alloying method

Effect of Milling Time and Reinforcement Volume Fraction on Microstructure and Mechanical Properties of SiCp-Reinforced AA2017 Composite Powder Produced by High-Energy Ball Milling

Effect of milling time on microstructure and hardness of AA7075-15 wt% SiC-1 wt% MWCNT nanocomposite

Production Technology Features for Aluminum Matrix Alloys with a Silicon Carbide Framework

The Microstructure and Properties of Fine Crystalline Al-50Si Alloy Prepared by High-Energy Ball Milling

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Effects of mechanically alloying Al2O3 and Y2O3 additives on the liquid phase sintering behavior and properties of SiC

Preparation of Intermetallic Compound MoSi2 by Mechanical Alloying Method

Experimental investigation on powder processing and its flow properties of AlSi10Mg alloy with niobium carbide for additive manufacturing

The Microstructures and Mechanical Properties of a 5vol%sic/aa2024 Nanocomposite Fabricated by Powder Metallurgy

Study on micro-grinding mechanism and surface quality of hardened 20 vol% SiCp/Al composites