Abstract:In the petroleum industry, the casing steel is fixed with a cement sheath to ensure reliable service in demanding conditions characterized by high temperature, high pressure, and exposure to multiple types of media. After the hydration of the cement, a porous material is produced with a highly alkaline solution filling the pores, commonly referred to as the pore solution. The casing will form a protective passive film when in contact with a highly alkaline pore solution. Nevertheless, once the cement sheath cracks, chloride ions in the stratum will pass through the cement sheath to the surface of the casing. When chloride ions accumulate to a certain concentration, the passive film will be destroyed, without exerting a protective influence on the substrate. After chloride ions come into direct contact with the casing, the casing is prone to severe failure due to corrosion perforation. The casing failure can cause a blowout outside the casing and even scrapping of the oil well. Controlling casing corrosion and ensuring casing integrity relies on understanding the critical chloride ion concentration that can cause the degradation of the passive film. Therefore, to assess the electrochemical properties and analyze the damage process of the passive film under varying chloride ion concentrations, several characterization techniques were employed. These included potential–time curves (E-t), polarization curves, electrochemical impedance spectroscopy (EIS), and Mott–Schottky curves. In addition, the composition of the passive film on the surface of the P110 casing steel was qualitatively analyzed using X-ray photoelectron spectroscopy (XPS). To further understand the surface morphology of the P110 casing steel, scanning electron microscopy (SEM) was used.

Slurry erosion behaviors of P110 steel and chromizing coating in liquid-solid two-phase flow

FORMATION OF CHROMIUM COATING AND COMPARATIVE EXAMINATION ON CORROSION RESISTANCE WITH 13crsteel INCO2-SATURATED SIMULATED OILFIELD BRINE

Experimental study on erosion wear behavior of PFA coated stainless steel tube

Fabrication of Wear and Corrosion Resisting G3 Alloy-Like Coating on P110 Steel by Double Glow Plasma Alloying

Anti-corrosion Performance of Chromium-coated Steel in a Carbon Dioxide-saturated Simulated Oilfield Brine

Experimental Study on Erosion of P110 Steel in Liquid-solid Two-phase Flow

Microstructure and Wear Resistance Analysis of TiC/Ni Composite Coating on P110 Steel by Argon Arc Cladding

Microstructure and Erosional Behavior of Erosion-Resistant Coatings of Super-Critical Boiler Pipes

Insights into the microstructure characteristics, mechanical properties and tribological behaviour of gas-phase chromized coating on GCr15 bearing steel

Experimental Research on Erosion of P110 Tubing During Perforating

Analyzing the mechanisms of Al2O3-TiO2 coating for enhanced slurry erosion resistance on AISI410 stainless steel

Effect of Flow Rate on the Corrosion Behavior of P110 Steel in High-Ca2+ and High-Cl− Environment

Electrochemical Investigation of Chloride Ion-Induced Breakdown of Passive Film on P110 Casing Steel Surface in Simulated Pore Solution: Behavior and Critical Value Determination

Research of CO_2 Corrosion Kinetics of Tubing and Casing Steel P110

Erosion Resistance of Casing with Resin and Metallic Coatings in Liquid–Solid Two-Phase Flow

Study on the Wear Performance of Surface Alloy Coating of Inner Lining Pipe under Different Load and Mineralization Conditions

Comparison of Surface Fractal Dimensions of Chromizing Coating and P110 Steel for Corrosion Resistance Estimation

Comparison on Tribological Properties Between Cu Coating and Ni-P Coating on P110 Oil Tube Steel Substrate

The Enhancement Effect of Salt Bath Chromizing for P20 Steel

Influence of Solid Chromizing Doped with Various Rare Earths on Microstructures and Properties of Cr-RE Coatings Fabricated by Pack Cementation

Corrosion Behavior of Oil Tube Steels under Conditions of Multiphase Flow Saturated with Super-Critical Carbon Dioxide