Abstract:The structural and tribological properties of a protective high-chromium coating synthesized on gray cast iron by air pulse-plasma treatments were investigated. The coating was fabricated in an electrothermal axial plasma accelerator equipped with an expandable cathode made of white cast iron (2.3 wt.% C–27.4 wt.% Cr–3.1 wt.% Mn). Optical microscopy, scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction analysis, microhardness measurements, and tribological tests were conducted for coating characterizations. It was found that after ten plasma pulses (under a discharge voltage of 4 kV) and post-plasma heat treatment (two hours of holding at 950 °C and oil-quenching), a coating (thickness = 210–250 µm) consisting of 48 vol.% Cr-rich carbides (M7C3, M3C), 48 vol.% martensite, and 4 vol.% retained austenite was formed. The microhardness of the coating ranged between 980 and 1180 HV. The above processes caused a gradient in alloying elements in the coating and the substrate due to the counter diffusion of C, Cr, and Mn atoms during post-plasma heat treatments and led to the formation of a transitional layer and different structural zones in near-surface layers of cast iron. As compared to gray cast iron (non-heat-treated and heat-treated), the coating had 3.0–3.2 times higher abrasive wear resistance and 1.2–1208.8 times higher dry-sliding wear resistance (depending on the counter-body material). The coating manifested a tendency of solidification cracking caused by tensile stress due to the formation of a mostly austenitic structure with a lower specific volume. Cracks facilitated abrasive wear and promoted surface spalling under dry-sliding against the diamond cone.

Influence of Solid Chromizing Doped with Various Rare Earths on Microstructures and Properties of Cr-RE Coatings Fabricated by Pack Cementation

Insights into the microstructure characteristics, mechanical properties and tribological behaviour of gas-phase chromized coating on GCr15 bearing steel

Growth Mechanism and Pore Formation of Solid Chromizing Layer of GCr15 Pin

Rare earth addition powered corrosion resistance of the surface oxide film on GCr15 bearing steel substrate

Rare earth effect on microstructure, mechanical and tribological properties of CoCrW coatings

Rare earth effect on the microstructure and wear resistance of Ni-based coatings

Effect of Cr on Wear Resistance and Mechanism of Preset-Powder Laser Cladding T15 Alloy Steel Coating

The Enhancement Effect of Salt Bath Chromizing for P20 Steel

Enhancing tribological performance of graphene sheet-embedded carbon films on steel substrates via texture engineering and chromium doping

Industrial Trials on the Cleanliness Improvement, Microstructure Refinement and Performance Enhancement of Rare‐Earth‐Treated 75Cr1 Steel

Microstructure and electronic structure of Cr2C and Fe2Y in the Cr-coating prepared by pack-cementation on the surface of ODS steel

The chromization on hot-rolled Fe40Mn20Cr20Ni20 high-entropy alloys by pack cementation

Evaluation of the Microstructure, Tribological Characteristics, and Crack Behavior of a Chromium Carbide Coating Fabricated on Gray Cast Iron by Pulsed-Plasma Deposition

MICROSTRUCTURE AND WEAR RESISTANCE OF CHROMIUM CARBIDE COATING IN SITU SYNTHESIZED BY VEB

Microstructure and Wear Resistance of FeCrV15 Coatings by Laser Cladding

Effect of Rare Earth Y on Microstructure and Mechanical Properties of High-Carbon Chromium Bearing Steel

Study on the Performance of Fe-Based Alloy Coating on 40Cr Substrate Surface

Deformation and Annealing Behavior of Cr Coating Prepared by Pack-Cementation on the Surface of Austenitic Stainless Steel

Effect of Chromium-Induced (fe, Cr)3C Toughness Improvement on the Two-Body Abrasive Wear Behaviors of White Cast Iron

Effects of rare earth elements addition on mechanical properties and corrosion behavior of GCr15 bearing steel under different heat treatment conditions

Effect of Rare-Earths Carburizing on Friction Behavior of GCr15 Steel Laser Melting Layer