Abstract:In order to solve the problem of shield hobbing cutter failure due to bias wear and chipping during tunnel boring, TiC-WC/Ni60 coating was prepared on the surface of H13 steel to improve the wear resistance of shield hobbing cutter. In this paper, four kinds of WC-TiC/Ni60 composite coatings with different content ratios of 5 wt% TiC+25 wt% WC, 10 wt% TiC+20 wt% WC, 15 wt% TiC+15 wt% WC and 20 wt% TiC+10 wt% WC were prepared on the surface of H13 steel by using the coaxial powder-feeding laser cladding equipment. The micromorphology, phase, hardness and friction and wear properties were fully studied. The results show that cross-sectional organization of the fused cladding layer mainly consists of columnar crystals, cytocrystals and equiaxial crystals; the hard phases in the fused cladding layer mainly consist of TiWC 2 , Cr 4 Ni 5 W, and Cr 3 C 2 , and so on; The microhardness of the cross-section of the fused cladding layer shows a trend of decreasing at first, then increasing and finally decreasing, and the highest hardness of the fused cladding layer occurs at the subsurface of the fused cladding layer; the friction coefficient of the fused cladding layer shows a trend of decreasing first and then increasing; the wear volume of the fused cladding layer is significantly lower than that of the substrate, and the wear volume of the 15 wt% TiC coating is the smallest of 1.313 mm 3 , which is 86.9 % lower than that of the substrate; the wear mechanism of the substrate is mainly abrasive wear and adhesive wear, and the wear mechanism of the fused cladding layer is mainly brittle spalling, abrasive wear and oxidative wear. The analysis of the experimental results shows that the surface properties of the coating are best when both TiC and WC contents are 15 wt%.

Microstructure and Wear Resistance Analysis of TiC/Ni Composite Coating on P110 Steel by Argon Arc Cladding

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

High Temperature Sliding Wear Behaviors of Ion Plating Tin Composite Coating with Ion Nitriding As Interlayer on Hot Work Die Steel

Microstructure and tribological properties of laser clad Ni-Ag/Tic composite coating

High-temperature wear and cyclic oxidation behavior of (Ti, W)C reinforced stainless steel coating deposited by PTA on a plain carbon steel

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

Effect of TiC addition on the microstructure and properties of laser cladding Ni60A coatings on H13 steel surface

Effect of SiC and TiC content on microstructure and wear behavior of Ni-based composite coating manufactured by laser cladding on Ti-6Al-4V

Raising the Wear Resistance of Chromium-Nickel Steel Surface-Hardened with Titanium Carbide Particles

Study on the performance of laser nitriding in situ enhanced Co12/TC4 composite Ag self-lubricating coating on TC4 surface

Microstructure and Wear Resistance of Laser Cladding nano TiC/micro TiB2/C-276 Composite Coatings on 316L Stainless Steel

Microstructure and Wear Resistance of Ti5Si3/Ti3Al Composite Coatings Prepared by Laser Cladding on TA2 Titanium Alloy

Microstructure and Wear Resistance of a Composite Coating Prepared by Laser Alloying with Ni-Coated Graphite on Ti-6Al-4V Alloy

Research on In-Situ Formation of Tic Particles Reinforced Nickel Base Alloy Coating Produced by Laser Cladding

Experimental Investigation on Tribological Performance of TiB2-CoTi Composite Coating Fabricated on AISI 304 Stainless Steel by Argon Arc Cladding Technique

Microstructural and Performance Analysis of (TiAl)95−xCu5Nix Coatings Prepared via Laser Surface Cladding on Ti–6Al–4V Substrates

Investigating the Microstructure and Wear Properties of AISI 4140 Steel Clad with WC-Ti Composite Particles Via Gas Tungsten Arc Welding

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Microstructure and Wear Resistance of In Situ Synthesized Ti(C, N) Ceramic-Reinforced Nickel-Based Coatings by Laser Cladding

Microstructure and Wear Resistance of Grx-Ti-BN Composite Coating on TC4 by Argon Arc Cladding

Corrosion and wear resistance of TiN/TiO2 composite ceramic coatings deposited by supersonic arc spraying