Abstract:The microstructure of Al-Cu-Li alloys is influenced by the alloying contents, which in turn affect the ultimate performance. This study examined the microstructure characteristics of Al-Cu-Li alloys with varying Li contents (1.05, 1.30, and 1.66 wt.%) in as-cast state, as well as microstructure evolution during homogenization treatments. The investigation employed a range of analytical techniques, including optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), X-ray diffraction (XRD), differential scanning calorimeter (DSC), focused ion beam (FIB), transmission electron microscopy (TEM), and thermodynamic calculation software. The findings indicate that the eutectic phase exhibited significant variations with the Li content changing. Three distinct low-melting phases were identified in 1.05Li alloy, including Ag-containing Al 2 CuMg, Al 7 Cu 4 Li, and Al 2 Cu. As Li content was elevated to 1.30 wt.%, there was a noticeable drop in the quantities of Ag-containing Al 2 CuMg and Al 7 Cu 4 Li phases. Conversely, the Al 2 Cu phase increased, and a few Al 2 CuLi phases emerged. When the Li raised to 1.66 wt.%, an increased Al 2 CuLi phase was discovered, which existed along the dendritic edges. However, there were only little Ag-containing Al 2 CuMg phase, and no Al 7 Cu 4 Li phase detected. The initial melting temperatures for the four soluble eutectic phases were systematically arranged in the following order: Ag-containing Al 2 CuMg < Al 7 Cu 4 Li < Al 2 Cu < Al 2 CuLi. The elevated Li content resulted in a challenge of dissolution of the eutectic phases. Following 500°C/12h homogenization process, the containing-Ag Al 2 CuMg phase dissolved. Additionally, the Al 7 Cu 4 Li and Al 2 Cu phases were eliminated through subsequent 515°C/12h homogenization. In addition, the Al 2 CuLi phase was still existing.

Homogenization heat treatment of 2099 Al–Li alloy

Microstructural Evolution and Kinetics of 7075 Al Alloy During Homogenization Treatment

Microstructural Evolution During Homogenization of DC Cast 7085 Aluminum Alloy

Microstructural Evolution of 2026 Aluminum Alloy During Homogenization

Effect of homogenization treatment temperatures on microstructure and properties of 6082 aluminum alloys

Effects of Homogenization Treatment on the Microstructure and Mechanical Properties of Mg–8Li–3Al–Y Alloy

Effect of Homogenization Treatment on Microstructure of 6063 Alloy

Microstructural Characterization of the As-Cast and Homogenized Al-Cu-Mg-Ag Alloy

Microstructure Evolution and Mechanical Properties of Homogenizing Treated Fully Lamellar Ti-46 Al-0 . 5 W0 . 5 Si Alloy

Homogenizing treatment of 7A55 alloy

Research on Homogenization Treatment of Mg-8wt.% Sn-1.5 Wt.% Al Alloy

Microstructure Evolution and Homogenization Kinetics of 15Cr–30Ni–Fe Heat‐Resistant Alloy

The Effect of the Homogenization Treatment with an Electric Field on Second Phase Precipitation of 2091 Al-Li Alloy During Ageing Treatment

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

Influence of enhanced Li content on the as-cast eutectic phase features and the evolution during homogenization of Al-Cu-Li alloys

Homogenization heat treatment of Mg-9.0Y-3.0MM-0.6Zr alloy

Microstructural Evolution of Al-Cu-Li Alloys with Different Li Contents by Coupling of Near-Rapid Solidification and Two-Stage Homogenization Treatment

Solidification Segregation Behavior and Homogenization Process of a Difficult-to-Deform Superalloy Used at 850 °C

Characterization of Al3Zr precipitation via double-step homogenization and recrystallization behavior after subsequent deformation in 2195 Al-Li alloy

Influence of homogenization treatment under an electric field on ductility of 2091 Al-Li alloy during hot rolling

Effects of homogenization on the microstructural evolution of a novel Zr and Er containing Al–Mg–Zn alloy