Abstract:The 2195 Al-Li alloy, as one of the representative third-generation Al-Li alloys, has extensive applications in lightweight aerospace structures. In this paper, the anisotropy in mechanical properties and microstructure evolution of 2195 Al-Li alloy sheets were investigated under a strain rate of 0.01, 0.1, 1 s-1 and a temperature of 440 and 500 °C. Experimental results showed that the hot tensile properties of the 2195 Al-Li alloy sheet exhibited a strong dependence on loading directions. The peak stress (PS) and elongation (EL) along the rolling direction (RD) were larger than the transverse direction (TD). For the tests carried out at 440 °C-1 s-1, the PS values of the sheets stretched along the RD and TD are 142.9 MPa and 110.2 MPa, respectively. And, most of the PS anisotropy values are larger than 15%. The anisotropy in EL is less significant than in PS. All the differences are about 10%. Moreover, dimples in the samples stretched along RD were more and deeper than those along TD at 440 °C. The fracture morphology along RD and TD were similar, and both were cleavage fractures at 500 °C. Particularly, the fractions of high angle grain boundaries (HAGBs) along TD were all about 5% larger than those of RD. And, there were more small-sized continuous dynamic recrystallization (CDRX) grains inside the initial grains and discontinuous dynamic recrystallization (DDRX) grains featured with the local bulge of grain boundaries along TD. This was due to the smaller average Schmid factor and the vertical EL trend of the initial grains when the samples were stretched along TD. A model of grain evolution during the dynamic recrystallization (DRX) along RD and TD was proposed based on EBSD results. The Schmid factor and banded structure had a more prominent effect on the hot ductility of the 2195 Al-Li alloy compared with the degree of DRX, thus presenting a higher EL and better hot ductility along RD.

Influence of homogenization treatment under an electric field on ductility of 2091 Al-Li alloy during hot rolling

The Effect of the Homogenization Treatment with an Electric Field on Second Phase Precipitation of 2091 Al-Li Alloy During Ageing Treatment

Study of the diffusion of Al–Li alloys subjected to an electric field

Effect of homogenization treatment under an electric field on T1 distribution and mechanical properties of 2091 Al-Li alloy

Effect of solution treatment in an electric field on mechanical properties and microstructure of 2091 Al-Li alloy

Effect of homogenization temperature on microstructural homogeneity and mechanical properties of twin-roll casted 8006 aluminum alloy

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Effect of Solution Treatment with Electric Field on Properties and Fracture Characters of Al-Li Alloys

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

Influence of enhanced Li content on the as-cast eutectic phase features and the evolution during homogenization of Al-Cu-Li alloys

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Microstructural Evolution and Kinetics of 7075 Al Alloy During Homogenization Treatment

Effects of Homogenization Treatment on the Microstructure and Mechanical Properties of Mg–8Li–3Al–Y Alloy

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effect of strain and dispersoids on abnormal grain growth, precipitation behavior and mechanical properties at longitudinal weld in Al-Li alloy profile

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Optimizing mechanical property of spray formed Al-Zn-Mg-Cu alloy by combination of homogenization and warm-rolling

Homogenization heat treatment influence on microstructure evolution and mechanical properties of as-cast Al-Li-Cu-Mg-Zr alloy for lightweight aerospace application