Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Atomic models of the structure of niobium silicides in Nb–Si in situ composites

Modeling creep behavior of niobium silicide in-situ composites

Analyses of Eutectoid Phase Transformations in Nb–Silicide In Situ Composites

Creep Mechanisms in Niobium-Silicide Based In-Situ Composites

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Creep Mechanisms in High-Temperature In-Situ Composites

Fracture of Laminated and In Situ Niobium Silicide-Niobium Composites

High-Temperature Creep of Nb–Si In Situ Composites

MICROSTRUCTURAL CHARACTERISTICS AND MECHANICAL PROPERTIES OF A Nb/Nb5Si3 BASED COMPOSITE WITH AND WITHOUT DIRECTIONAL SOLIDIFICATION

The balance of mechanical and environmental properties of a multielement niobium-niobium silicide-basedIn Situ composite

A Study of the Effects of Hf and Sn on the Microstructure, Hardness and Oxidation of Nb-18Si Silicide-Based Alloys-RM(Nb)ICs with Ti Addition and Comparison with Refractory Complex Concentrated Alloys (RCCAs)

On Nb Silicide Based Alloys: Alloy Design and Selection

Niobium-Base Refractory Alloys with Silicide and Carbide Hardening Current Status and Prospects

On the oxidation mechanism of niobium-base in situ composites

High-temperature Nb-Si composites. Part 2

On the Alloying and Properties of Tetragonal Nb5Si3 in Nb-Silicide Based Alloys

In-Situ Observation of Ni-11.5wt%Si Eutectic Microstructure Evolution and Exploration of Strengthening Mode of Ni-Ni3si Eutectic Composites

Characterization of A New Nb-Silicide (-Nb11si4) in Nb-Si Binary Systems

Prediction of New Structure, Phase Transition, Mechanical, and Thermodynamic Properties of Nb3Si

Study of the Microstructure and Phase Composition of Crude Niobium Electron-Beam Remelting Sublimates