Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

In-Situ Observation of Ni-11.5wt%Si Eutectic Microstructure Evolution and Exploration of Strengthening Mode of Ni-Ni3si Eutectic Composites

Microstructure, Mechanical Properties and Thermal Stability of Ni-Based Single Crystal Superalloys with Low Specific Weight

The formation mechanism of eutectic microstructures in NiAl-Cr composites

Microstructure Evolution and Toughening Mechanism of a Nb-18Si-5HfC Eutectic Alloy Created by Selective Laser Melting

Effect of metastable phase content controlled by heat-treatment on corrosion behavior of directionally solidified Ni-12 wt%Si hypereutectic composites

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Microstructural Investigations of Ni-Based Superalloys by Directional Solidification Quenching Technique

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

Thermal modification of brittle CoFeNi2(Ti3Si5)0.16 eutectic high-entropy alloy by annealing treatment

Temperature-Dependent Mechanical Behaviors and Deformation Mechanisms in a Si-Added Medium-Entropy Superalloy with L12 Precipitation

Influence of Ni Contents on Microstructure and Mechanical Performance of AlSi10Mg Alloy by Selective Laser Melting

In-situ observations of solidification process of Fe–Al–Ta eutectic alloy

Analyses of Eutectoid Phase Transformations in Nb–Silicide In Situ Composites

Microstructure evolution and mechanical properties of TC4/Ni metallic-intermetallic laminated composites: Formation and strengthening effects of Ti2Ni phases

In-Situ High-Energy Synchrotron X-Ray Diffraction Study of Micromechanical Behavior of Multiple Phases in Ni47ti44nb9 Shape Memory Alloy

Microstructural evolution and mechanical property of a SiCf/SiC composite/Ni-based superalloy joint brazed with an Au-Cu-Ti filler

Design, microstructure and thermal stability of a novel heat-resistant Al-Fe-Ni alloy manufactured by selective laser melting

High-temperature Mechanical Properties and Dynamic Recrystallization Mechanism of in situ Silicide-reinforced MoNbTaTiVSi Refractory High-entropy Alloy Composite

Microstructure evolution behavior of Ni3Al (γ′) phase in eutectic γ-γ′ of Ni3Al-based alloy

High throughput in-situ synthesis of Fe-Cr-Ni alloys via laser powder bed fusion: exploring the microstructure and property evolution

Performance Study and Heat Treatment Analysis of Selective Laser Melting SiC/18Ni300 Martensitic Mold Steel Composites