Abstract:Synthesis of nanocomposites is challenging due to the difficulties in achieving homogeneous distribution of reinforcing particles in metal. In this paper, an in‐situ Al‐MgAl2O4 nanocomposite billet was prepared by the reaction of ɣ‐Al2O3 with molten Al and ultrasonication‐assisted impeller mixing. The microstructure of the composite showed homogeneously distributed MgAl2O4 crystals alongside their clusters in the Al matrix. Microstructural analysis revealed MgAl2O4 crystals distributed from 20 nm to 4 μm in size. The hardness was found to vary within the composite from 50 Hv for the matrix to 140 Hv for particle cluster regions. The grain size was reduced from 1000 μm in reference metal (CP Al) to 100 μm in the composite. The compression strength of the composite was increased substantially and higher strain hardening effect in comparison with Al was noticed in the compression test. The signatures of extensive plastic deformation such as dislocation pileups, deformed grains, grain boundary pinning etc. were observed in the composite via transmission electron microscopy. Damping properties of as‐cast composite were higher than those of CP Al in the temperature range from room temperature to 350 °C. After rolling the composite up to 40% reduction, the damping capacity (Tanδ) of the composite was found to increase marginally after 150 °C. Higher damping was found to reoccur after the annealing treatment of the composite. The improvement in damping capacity at RT was possibly influenced by the micron sized MgAl2O4 and at higher temperatures by the nano‐sized MgAl2O4 crystals. The reoccurrence of higher damping in the annealed composite underlined the stability of finer grains due to the grain boundary pinning by nano‐sized MgAl2O4 crystals. The studies on the damping property of the composite displayed the benefits of having dual size distribution of MgAl2O4 crystals (nm and μm) in the composite. This article is protected by copyright. All rights reserved.

Net-shape forming of bi-continuous Al2O3/Al composite by displacement reaction

High-Resolution Electron Microscope Observation of Interface Microstructure of A Cast Al-Mg-Si-Bi-Pb(6262)/Al2o3p Composite

Bi-continuous Metal Matrix Composites

FLEXURAL STRENGTH OF IN-SITU REACTION PROCESSED Al2O3-Al3Ti-Al COMPOSITES

Co-continuous Al/Al2O3 composite produced by liquid displacement reaction: Relationship between microstructure and mechanical behavior

Microstructure and properties of in-situ Al–Si/Al2O3 composites prepared by displacement reaction

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Processing of in situ aluminum-matrix composites and controlling of the solidification microstructures

FORMATION OF COMPOSITE MATERIAL OF METAL/TWO-PHASE CERAMIC WITH VAGUE INTERFACE BY IN SITU OXIDATION OF MOLTEN ALUMINUM ALLOY

Interface Reaction and Thermodynamic Analysis on Al2o3-Sio2(Sf)/Az91d Composite

Evaluation of the microstructure of in-situ reaction processed Al3Ti-Al2O3-Al composite

Interfacial research on interpenetrating network structure ZrO2/Al-Mg composites prepared by Extrusion Freeform Fabrication 3DP and pressureless infiltration

Microstructure and Performance of Nanometer Γ-Al2o3p/al Composite Fabricated in Al-Co3O4 Components

Inorganic/inorganic composites through emulsion templating

Interfacial reactions in K2Ti6O13(w)/Al2O3/Al composite

The Role of the Displacement Reaction in the Production of Surface Composite Layer

Microstructural evolution and property evaluation of in‐situ Al‐MgAl2O4 nanocomposite prepared by ɣ‐Al2O3 and ultrasonication‐assisted impeller mixing

Microstructure and properties of Al(2)O(3)sf/Al -1.5Mg composite manufactured by extrusion directly following liquid infiltration

Fabrication and Mechanical Properties of Particle Dispersed Al-Al2O3 Composite Materials.