Abstract:Synthesis of nanocomposites is challenging due to the difficulties in achieving homogeneous distribution of reinforcing particles in metal. In this paper, an in‐situ Al‐MgAl2O4 nanocomposite billet was prepared by the reaction of ɣ‐Al2O3 with molten Al and ultrasonication‐assisted impeller mixing. The microstructure of the composite showed homogeneously distributed MgAl2O4 crystals alongside their clusters in the Al matrix. Microstructural analysis revealed MgAl2O4 crystals distributed from 20 nm to 4 μm in size. The hardness was found to vary within the composite from 50 Hv for the matrix to 140 Hv for particle cluster regions. The grain size was reduced from 1000 μm in reference metal (CP Al) to 100 μm in the composite. The compression strength of the composite was increased substantially and higher strain hardening effect in comparison with Al was noticed in the compression test. The signatures of extensive plastic deformation such as dislocation pileups, deformed grains, grain boundary pinning etc. were observed in the composite via transmission electron microscopy. Damping properties of as‐cast composite were higher than those of CP Al in the temperature range from room temperature to 350 °C. After rolling the composite up to 40% reduction, the damping capacity (Tanδ) of the composite was found to increase marginally after 150 °C. Higher damping was found to reoccur after the annealing treatment of the composite. The improvement in damping capacity at RT was possibly influenced by the micron sized MgAl2O4 and at higher temperatures by the nano‐sized MgAl2O4 crystals. The reoccurrence of higher damping in the annealed composite underlined the stability of finer grains due to the grain boundary pinning by nano‐sized MgAl2O4 crystals. The studies on the damping property of the composite displayed the benefits of having dual size distribution of MgAl2O4 crystals (nm and μm) in the composite. This article is protected by copyright. All rights reserved.

Microstructure and properties of in-situ Al–Si/Al2O3 composites prepared by displacement reaction

Effect of high energy ball milling on the displacement reaction in particulate reinforced Al–Si–Cu alloy matrix composite powders

Effect of high energy ball milling on displacement reaction and sintering of Al−Mg/SiO2 composite powders

Preparation and Mechanical Properties of in Situ Submicron MgAl2O4p/6061Al Composites from Al–Mg–SiO2 System

Microstructures and Mechanical Properties of in Situ Al 2 O 3 /Al-Si Composites Fabricated by Reaction Hot Pressing

Preparation of TiAl-based alloys by mechanical milling and reactive sintering

In situ processing and aging behaviour of an aluminium/Al2O3 composite

Microstructure and Properties of A Tial Alloy Prepared by Mechanical Milling and Subsequent Reactive Sintering

In Situ Al Based Composites Fabricated in Al-SiO2-C System by Reaction Sintering

Microstructure and Mechanical Properties of In-Situ Α-Al2o3p/al-12si Composites Fabricated by Direct Melt Reaction Method with Aid of Electromagnetic Stirring

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Microstructural evolution and property evaluation of in‐situ Al‐MgAl2O4 nanocomposite prepared by ɣ‐Al2O3 and ultrasonication‐assisted impeller mixing

Synthesis and Characterization of in Situ (al 2 O 3 –si)/al Composites by Reaction Hot Pressing

Structure Investigation of Ball Milled Composite Powder Based on AlSi5Cu2 Alloy Chips Modified by Sic Particles

INFLUENCE OF MILLING TIME ON GROWTH MORPHOLOGY AND MECHANICAL PROPERTIES OF ALUMINUM-SILICON-CARBIDE COMPOSITES

Net-shape forming of bi-continuous Al2O3/Al composite by displacement reaction

Effect of mechanical milling on diffusive reaction of Ti-Al composite powders

In situ studies on temperature‐dependent deformation mechanisms of Al2O3 prepared by spark plasma sintering

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Co-continuous Al/Al2O3 composite produced by liquid displacement reaction: Relationship between microstructure and mechanical behavior