Abstract:High performance lightweight structures made of metal matrix composites (MMCs) are in demand for application in variety of industries such as aircraft, spacecraft, automobile, marine, sports equipment, etc. However, uniform distribution of the reinforcement phase to improve the mechanical properties and quality of MMCs has been the challenge for the manufacturing industries. Hence, researchers are focusing on the development of traditional low-cost method of producing metal matrix composites. In the view of above facts, an attempt is made to study the processing and characterization of Si-Al alloy reinforced with zirconium dioxide particulate composites in this paper. Hence, this paper concentrates on experimentally identifying the effect of stir cast and spray forming processing techniques followed by hot pressing on micro hardness, compressive strength, and tensile strength using Taguchi’s design of experiments for aluminum silicon matrix alloy reinforced with zirconium dioxide particulates. From the extensive experimentation on aluminum and silicon reinforced with the ZrO2 powder particulates, it was observed that there was an improvement in selected mechanical properties as the percentage of ZrO2 increased with 13 wt.% of silicon under spray forming processing technique compared to stir cast composites. This may be due to uniform distribution homogenous dispersion, larger work hardening rate, and structure of dislocation tangles around the ZrO2 particulates that occurred during spray forming processing technique. Further, results obtained from the interaction plot, contour plot, main effects plot, and analysis of variance (ANOVA) proved to be successful for identifying the optimum processing parameters for Si-Al alloy reinforced with zirconium dioxide particulate composites. Further, this paper also discusses wear study using pin on disc wear testing apparatus on spray forming processed aluminum and silicon (13.0 wt.%) alloy reinforced with the ZrO2 powder particulates based on Taguchi’s design of experiments followed by second order model generation for wear using response surface methodology. Finally, electrode wear study of spray forming processed aluminum and silicon alloy reinforced with the ZrO2 powder particulates using electric discharge machining by varying peak current (A), pulse on time (μs), and pulse off time (μs) using brass, copper, and graphite as electrode material based on L27orthogonal array. The understanding gained from the design of experiments in this paper can be used to develop future guidelines for processing and characterization of Si-Al alloy reinforced with zirconium dioxide particulate composites.

Use of Squeeze Infiltration Processing for Fabricating Micro Silica Reinforced Aluminum Alloy-based Metal Matrix Composite

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Novel MMC Microstructures Prepared by Melt Infiltration of Reticulated Ceramic Preforms

Microstructures and Mechanical Properties of Engineered Short Fibre Reinforced Aluminium Matrix Composites

Analysis of a squeeze cast magnesium alloy with Aluminium metal matrix composites

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Development of alumina reinforced aluminum metal matrix composite with enhanced compressive strength through squeeze casting process

An integrated experimental and analytical approach on mechanical characterization of advanced powder metallurgy aluminium metal matrix composites reinforced with different particulates

Prediction of tensile strength in squeeze casted hybrid aluminium matrix composites using conventional statistical approach

Sensitivity Analysis of Reinforced Aluminum Based Metal Matrix Composites

Applications of reinforcement particles in the fabrication of Aluminium Metal Matrix Composites by Friction Stir Processing - A Review

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Developments in the aluminum metal matrix composites reinforced by micro/nano particles – A review

Processing, Mechanical Characterization, and Electric Discharge Machining of Stir Cast and Spray Forming-Based Al-Si Alloy Reinforced with ZrO2 Particulate Composites

Fabrication of Alumina Silicate Short Fibers Reinforced AZ91 Metal Matrix Composites

Processing and Characterization of AA2618/Sicp Metal Matrix Composites by Stir Casting Method

Processing of Aluminium-Silicon Alloy with Metal Carbide as Reinforcement through Powder-Based Additive Manufacturing: A Critical Study

Evaluation of Mechanical Properties of Aluminum-Silicon Carbide Metal Matrix Composite

Processing of silica bonded porous SiC preform for metallic composites

Optimization of Squeeze Casting Process Parameters on AA8011 Based Hmmcs Under NaCl Environment

Fabrication of fiber reinforced metal matrix composites by squeeze casting technology