Abstract:AlSi10Mg is the most widely processed material among the Al-Si-Mg family by utilizing additive manufacturing routes. Properties such as corrosion resistance, low density and high specific strength open the door to be a competitive material in aerospace and automotive industries. AlSi10Mg alloy of 80 × 25 × 5 mm rectangular pieces was manufactured using a laser-assisted powder bed fusion route and subsequently solutionized at 520 °C for 2 hours. Solution-treated samples were cold rolled to 20, 40 and 60% reduction with multi-passes. Samples were rotated by 90° between the passes. The current work aims at assessing the effect of cold cross-rolling on the microstructure and hardness. Optical, scanning electron microscope and XRD were used for characterization. The density of the as-built, solution treated, and cold-rolled samples was measured using Archimedes' principle. The optical microstructure of the as-built sample revealed the melt pool boundaries on the surface and fish scale morphology in the transverse plane. Scanning electron microstructure of the as-built sample revealed the silicon network surrounding the alpha aluminum cells. Solution heat treatment has resulted in the formation of discrete Si particles in the matrix. There was not much difference in the size of the aluminum cells and Si particles with respect to the percentage rolling reductions or on the other hand rolling has not brought any change in the microstructural morphology. However, the increase in hardness upon increasing the percentage reduction in thickness is mainly attributed to the phenomenon of dislocation strengthening. The 60% cold rolled specimen showed a 35 and 142% increase in hardness as compared to as-built and as-cast alloy respectively. XRD pattern has clearly indicated the Al and Si peaks. The crystallite size decreased with an increase in percentage rolling while the lattice strain had the opposite effect.

Effect of Combined Repetitive Corrugation and Straightening and Rolling on the Microstructure and Mechanical Properties of Pure Aluminum

Strain inhomogeneity and grain refinement in AA6063 aluminum alloy subjected to repetitive corrugation and straightening: comparison of experimental and finite element analysis

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Characterisation of Microstructure, Texture and Mechanical Properties of Pure Aluminium Sheets Severely Deformed by Constrained Groove Pressing and Subsequent Cold Rolling

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

The Effect of Cold Rolling on the Corrosion Behaviour of 5083 Aluminium Alloys

Effect of Ultrasonic Surface Rolling Process on Surface Properties and Microstructure of 6061 Aluminum Alloy

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy

Effect of Cross-Rolling on the Hardness of the AlSi10Mg Alloy Fabricated through Powder Bed Fusion

Effects of Heat-Treatment and Cold-Rolling on Mechanical Properties and Impact Failure Resistance of New Al 6082 Aluminum Alloy by Continuous Casting Direct Rolling Process

Microstructural Evolution and Mechanical Properties of Multi-layered Aluminum Alloy 6061 Processed by Accumulative Roll Bonding

Effect of Single-Pass Rolling on Microstructure and Mechanical Properties of AZ31 Alloy Processed by Equal Channel Angular Pressing

Effect of rolling deformation on microstructure and mechanical properties of Mg–Y–Nd–Al alloy

The improvement on mechanical anisotropy of AZ31 magnesium alloy sheets by multi cross-rolling process

Evolution of texture and microstructure during accumulative roll bonding of aluminum AA5086 alloy

Effect of Rolling and Annealing on Microstructure and Mechanical Properties of High Purity Aluminum

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

Improving mechanical anisotropy and corrosion resistance of extruded AA7075 alloy by warm cross rolling and annealing

Microstructure evolution of AZ91 alloy processed by a combination method of equal channel angular pressing and rolling