Abstract:For silicon solar cells, polysilicon‐based passivating contacts exhibit excellent gettering effects during high‐temperature fabrication process. This study confirms that both n‐ and p‐type polysilicon passivating contacts show stable and robust performance to iron gettering. However, iron gettering to the front p‐type emitter is found to degrade the emitter saturation current. The polysilicon‐based solar cells with significant initial bulk iron contamination exhibit lower Voc and Jsc values, interestingly, as well as an increased ideality factor and worse temperature coefficient in Voc. Over the past decade, silicon solar cells with carrier‐selective passivating contacts based on polysilicon capping an ultra‐thin silicon oxide (commonly known as TOPCon or POLO) have demonstrated promising efficiency potentials and are regarded as an evolutionary upgrade to the PERC (passivated emitter and rear contact) cells in manufacturing. The polysilicon‐based passivating contacts also exhibit excellent gettering effects that relax the wafer and cleanroom requirements to some extent. In this work, we experimentally explore the impact of bulk iron contamination and polysilicon gettering on the passivation quality of the polysilicon/oxide structure and the resulting solar cells performance. Results show that both n‐ and p‐type polysilicon/oxide passivating contacts are not affected by iron gettering, demonstrating robust and stable passivation quality. However, for a very high bulk iron contamination (1 × 1013 cm−3), the accumulated iron in the p‐type lightly boron‐doped emitter in crystalline silicon would degrade the emitter saturation current density. This can cause a reduction in both open‐circuit voltage and short‐circuit current. Meanwhile, this very high iron content (1 × 1013 cm−3) can further degrade the fill factor and temperature coefficient of the cells. On the other hand, for an initial iron content of 2 × 1012 cm−3, which should be well above the iron level in the current industrial Czochralski silicon wafers, the resulting cells demonstrate similar performance as the control group with no intentional iron contamination. This work brings attention to both the benefits of polysilicon gettering effects as well as the potential degradation due to the accumulation of metal impurities in the p‐type emitter region.

Direct Observation of the Impurity Gettering Layers in Polysilicon-Based Passivating Contacts for Silicon Solar Cells

Impurity Gettering by Boron‐ and Phosphorus‐Doped Polysilicon Passivating Contacts for High‐Efficiency Multicrystalline Silicon Solar Cells

Effect of Iron Contamination and Polysilicon Gettering on the Performance of Polysilicon‐Based Passivating Contact Solar Cells

Polysilicon Passivating Contacts for Silicon Solar Cells: Interface Passivation and Carrier Transport Mechanism

Direct observation of the distribution of impurity in phosphorous/boron co-doped Si nanocrystals

Phosphorus-diffused polysilicon contacts for solar cells

Phosphorus-doped polycrystalline silicon passivating contacts via spin-on doping

Solution-Doped Polysilicon Passivating Contacts for Silicon Solar Cells

Poly-Si passivating contacts prepared via phosphorus spin-on-doping: A comparison between different silicon deposition methods

Effect of Surface Texture on Pinhole Formation in SiO x-Based Passivated Contacts for High-Performance Silicon Solar Cells

Role of polysilicon in poly-Si/SiOx passivating contacts for high-efficiency silicon solar cells

Current status and challenges for hole-selective poly-silicon based passivating contacts

Impurity Gettering by Atomic-Layer-Deposited Aluminium Oxide Films on Silicon at Contact Firing Temperatures (Phys. Status Solidi RRL 3/2018)

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

Design Rule of Electron- and Hole-Selective Contacts for Polycrystalline Silicon-Based Passivating Contact Solar Cells

Application of Phosphorus‐Doped Polysilicon‐Based Full‐Area Passivating Contact on the Front Textured Surface of P‐type Silicon

Optimizing Phosphorus-Doped Polysilicon in TOPCon Structures Using Silicon Oxide Layers to Improve Silicon Solar Cell Performance

In Situ Reflectometry and Diffraction Investigation of the Multiscale Structure of p-Type Polysilicon Passivating Contacts for c-Si Solar Cells

Improving the Performance of Industrial TOPCon Solar Cells Through the Insertion of Intrinsic A-Si Layer

Enhancing the Selectivity and Transparency of the Electron Contact in Silicon Heterojunction Solar Cells by Phosphorus Catalytic Doping

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer