Abstract:It is suggested that fatigue failure mechanisms in the face-centered cubic metals are greatly affected by stacking fault energy. It was from this viewpoint that the fatigue crack initiation and stage I type crack propagation in 18-8 austenitic steel which had the lowest stacking fault energy among the face-centered cubic metals on the market, were discussed by the X-ray microbeam diffraction technique and the replica electron microscopic method.The fatigue slip line at room temperature tests has fine and straight configurations which are characteristic of low stacking fault energy materials, while the wavy and coarse slip line is typical of fatigue tests at 200°C where screw dislocation is more easily prone to cross slip. In both of these cases very complicated deformation configurations are caused by double slip and cross slip near the grain boundaries, and frequent extrusion and intrusion are observed in these areas. Fatigue crack nucleation might be caused by stress concentration at the notch and peak topography. The stage I type fatigue crack propagates immediately after the initiation, mainly along and frequently across the intense slip lines. Its growth in the area neighbouring the grain boundary runs in the direction that depends on both the crystal orientations of the grain containing the crack and the grains adjacent to it.Total misorientation and micro lattice strain measured by X-ray micro-beam diffraction technique increase abruptly at early fatigue stressing, then equilibrium values are attained and finally increase rapidly. These three periods during the fatigue deformation might be corresponding to those of the fine slip line initiation, the intensification of each slip line without new slip line formation and of final initiation of micro crack, respectively. Furthermore it will be noticed that the equilibrium value of total misorientation of 18-8 austenitic steel during the fatigue process is about one-tenth of that of carbon steel.The area of substructural zone near the fatigue crack of 18-8 austenitic steel is smaller than that of aluminum of high stacking fault energy and body-centered cubic iron. Therefore, the formations of subgrain and martensite could not be detected by X-ray micro-beam diffraction technique when irradiated by Cr-Kα of 200μφ beam size. In order to clarify these points the detailed observation at the fatigue crack tip must be made by using transmission electron microscopy. These results will be reported elsewhere.

Propagation Behavior of Small Fatigue Crack in Carbon Steel Thin Film under Cyclic Pure Shear Loading.

Slip and Crack Initiation Behavior of Carbon Steel Thin Films under Cyclic In-Plane Shear Loading

Microscopic Analysis by EBSD Method on Fatigue Crack Propagation Behaviour in Ultrafine-Grained Copper

Short Fatigue-Crack Growth from Crack-like Defects under Completely Reversed Loading Predicted Based on Cyclic R-Curve

Microscopic Observations of Fatigue Crack Initiation Process in 18-8 Austenitic Steel

Cracking in a Fe–25Mn–3Si–3Al Steel

Micro-Defect Effect on Gigacycle Fatigue S-N Property and Very Slow Crack Growth of High Strength Low Alloy Steel

Frictional Sliding of Microcracks under Compression

Effect of microstructure and local stress on small crack initiation and propagation paths in coarse‐grained FeCrAl alloys

Effect of Microstructure on Fatigue-Crack Propagation of 18CrNiMo7-6 High-Strength Steel

Analysis of fatigue fracture with cyclic overloading for A537 steel in 3.5%NaCl solution at an applied cathodic potential

In-situ observation of strain evolution and ratchetting of growing fatigue cracks

Prediction of Fatigue Crack Propagation Path from a Pre-Crack under Combined Torsional and Axial Loading

Effect of microstructure on small fatigue crack initiation and early propagation behavior in super austenitic stainless steel 654SMO

Simple Predicting Method for Fatigue Crack Growth Rate Based on Tensile Strength of Carbon Steel

In Situ Study of Cementite Deformation and Its Fracture Mechanism in Pearlitic Steels

Crystallographic analysis on small fatigue crack propagation behaviour of a nickel‐based single crystal superalloy

Microstructural Dependence of Anisotropic Fracture Mechanisms in Cold-Drawn Pearlitic Steels

Creep-Fatigue Crack Initiation Simulation of a Modified 12% Cr Steel Based on Grain Boundary Cavitation and Plastic Slip Accumulation

Mechanistic model for hydrogen accelerated fatigue crack growth in a low carbon steel

BEHAVIOR OF SHORT FATIGUE CRACKS IN MEDIUM CARBON BAINITIC BACK-UP ROLL STEEL UNDER MILD TRACTIVE ROLLING CONTACT