Abstract:Magnetorheological elastomers (MRE) are intelligent controllable materials used as polishing pads in chemical mechanical polishing (CMP), and the magnetic particles in the MRE polishing pad are used as solid-phase catalysts for heterogeneous Fenton reactions for oxidizing single-crystal SiC surfaces, thereby helping reduce the processing difficulty and obtain high-quality surfaces. The influence of the solid-phase catalyst (Fe3O4 mass fraction, particle size) and polishing solution environment (H2O2 concentration, pH value) on the CMP heterogeneous Fenton reaction polishing single-crystal SiC were investigated. The material removal behavior of the MRE polishing pad was investigated. The results demonstrated that the solid-phase catalyst, Fe3O4, has a better superior effect than the carbonyl iron powder (CIP). The polishing material removal rate (MRR) increased and the surface roughness (Ra) decreased with an increase in the Fe3O4 mass fraction. Superior polishing results were obtained at a particle size of 0.3 μm. The higher the H2O2 concentration in the polishing solution, the greater the MRR, with lower Ra at 10% concentration. The highest MRR and lowest Ra were achieved at pH = 3 in acidic environments. During polishing, the heterogeneous Fenton reaction can significantly enhance the removal ability of polishing materials. The MRR increased by 33.4% with the heterogeneous Fenton reaction compared with those without the heterogeneous Fenton reaction, and the contribution of the heterogeneous Fenton reaction to total material removal was 25.03%. The analysis of the SiC–Abrasive–MRE polishing pad contact state revealed that the heterogeneous Fenton reaction can oxidize the SiC surface and reduce the surface hardness, increasing the indentation depth δwa of the abrasive grain into the SiC surface and exhibiting greater material removal.

Study of the polishing slurry dispersant for chemical mechanical polishing of 304 stainless steel

Study on Chemical Action Mechanism of Ferric Chloride-Based Polishing Slurry in CMP of 304 Stainless Steel

Electrochemical Analysis of the Slurry Composition for Chemical Mechanical Polishing of Flexible Stainless-Steel Substrates

Methods and Mechanistic Analysis of Improving the Dispersion of Nano Silica Colloidal Particles in Chemical Mechanical Polishing Slurries

The Effect of Sodium Hexametaphosphate on the Dispersion and Polishing Performance of Lanthanum–Cerium-Based Slurry

Optimizing of the Colloidal Dispersity of Silica Nanoparticle Slurries for Chemical Mechanical Polishing

Improvement in dispersion stability of alumina suspensions and corresponding chemical mechanical polishing performance

Influence of Slurry Ingredients as Particle on Hard Disk Substrate Polishing

Potassium persulfate as an effective oxidizer for chemical mechanical polishing of GCr15 bearing steel

High-performance chemical mechanical polishing slurry for aluminum alloy using hybrid abrasives of zirconium phosphate and alumina

Investigation of Polisher Head and Slurry Sweep Effect in Oxide Film Polishing

Performance of Sodium Dodecyl Sulfate in Slurry with Glycine and Hydrogen Peroxide for Copper-Chemical Mechanical Polishing

Chemical Mechanical Polishing of Aluminum Alloys using Alumina-Based Slurry

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

A Novel Approach of Chemical Mechanical Polishing for a Titanium Alloy Using an Environment-Friendly Slurry

Chemical Mechanical Polishing of Mo Using H2O2 as Oxidizer in Colloidal Silica Based Slurries

Influence of Colloidal Silica Dispersion on the Decrease of Roughness in Silicon Chemical Mechanical Polishing

Study on heterogeneous Fenton reaction parameters for polishing single-crystal SiC using magnetorheological elastomers polishing pads

Experimental study on ultrasonic-assisted electrolyte plasma polishing of SUS304 stainless steel

Preliminary Study on Fluidized Bed Chemical Mechanical Polishing (FB-CMP) Process for Stainless Steel 304 (SS304)

Study on Oxidant in Chemical Mechanical Polishing of Copper