Abstract:In this present work, Ni3Si–Al2O3 nanocomposite powders were synthesized by mechanical milling using NiO, Si and Al as raw materials. The phase transformation, formation mechanism and microstructure evolution of the powders during mechanical milling were investigated by X-ray diffraction (XRD), differential thermal analysis (DTA), scanning electron microscopy (SEM), transition electron microscopy (TEM) and microhardness measurements. Results showed that the Ni3Si, Al2O3 and Ni31Si12 phases formed after 5 h of milling with a rapid mechanically induced self-propagating synthesis mode. The average grain size and internal strain of Ni3Si and Al2O3 after 30 h of milling were (16.8 nm, 1.27%) and (19.6 nm, 0.94%), respectively. The maximum microhardness value of 813 HV was obtained in the 30 h milled powder. The relationship between the hardness and grain size of the powders satisfies the Hall–Petch relationship. Ni3Si–Al2O3 nanocomposite powders are very stable during heating at 950 °C. By annealing of the milled powders leads to grain growth, internal strain and microhardness of Ni3Si powder decrease and transformation of disordered structure to an ordered state. A long-range ordering parameter (LRO) of 0.97 for the ordered Ni3Si can be achieved after annealing at 950 °C for 2 h.

Characterization and Formation Mechanism of Ni3Si–Al2O3 Nanocomposite Prepared by Mechanochemical Reduction Method

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Characterization of Mo–Si–B Nanocomposite Powders Produced Using Mechanical Alloying and Powder Heat Treatment

Nanostructured Composite Obtained by Mechanically Driven Reduction Reaction of Cuo and Al Powder Mixture

Nanocrystalline Ni-30wt%Fe Supersaturated Solid Solution Synthesized by Mechanical Alloying

Microstructure and formation mechanism of Ni-Al intermetallic compounds fabricated by reaction synthesis

Effect of Al<sub>2</sub>O<sub>3</sub> particle size on the microstructure, phase transformation and mechanical properties of hot pressed Al<sub>2</sub>O<sub>3</sub>-CA6-ZrO<sub>2</sub>/Ni multi-phase composites

Milling parameter optimization for refinement of NiO/Al mixtures and synthesis of Ni/Al2O3 nanocomposites

Effect of Al2O3 particle size on the microstructure, phase transformation and mechanical properties of hot pressed Al2O3-CA6-ZrO2/Ni multi-phase composites

Research of nanocrystalline Ni-30%Fe solid solution synthesized by mechanical milling

Effect of nano-Al2O3 addition on microstructure and mechanical properties of Ti2AlNb-based composites prepared by powder metallurgy

Study on synthesis and structure of mechanically alloyed W-Ni-Fe nanocomposite powders

Microstructure and thermal stability of MoSi2-CoNiCrAlY nanocomposite feedstock prepared by high energy ball milling

Microstructure and mechanical properties of in situ NiAl-Mo2C nanocomposites prepared by hot-pressing sintering

Mechanical properties and superplasticity of the Ni/Si3N4(W) nanocomposite fabricated by electrodeposition

Influence of Ni Contents on Microstructure and Mechanical Performance of AlSi10Mg Alloy by Selective Laser Melting

Fabrication of Ni/Sic Composite Powder by Mechanical Alloying and Its Effects on Properties of Copper Matrix Composites

Mechanical Properties and Microstructure of Sic-Zro2(3y)-Al2o3 Nanocomposites

Magnetic properties and Structural characterization of nanocrystalline Fe-20%A (Ni, Co and Si) alloys powders synthesized by mechanical alloying process

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Formation of Al<sub>3</sub>Ni nanofibers in an Al-based metal matrix composite fabricated by reaction sintering