Abstract:Thermal sprayed NiCr-Cr3C2-CaF2/BaF2 composite coatings can be used as high-temperature wear-resistant material for aeroengine brush seal runway. High temperature friction and wear produces a coupling stress field formed by the superposition of thermal stress and friction stress. At the same time, the morphology and properties of each phase in the composite coating will have a significant impact on the coupling stress field. The thermal-mechanical coupling stress field simulation study of multiphase composite coatings under high temperature friction and wear conditions is still insufficient. The coupling stress distribution is simulated by finite element method to predict the potential failure mode of the coating and provide a basis for the design of brush sealing coating. Based on Voronoi polygon, the crystal micro finite element model of NiCr-Cr3C2-CaF2/BaF2 multiphase composite coating is established. The proportion, distribution morphology and thermal-mechanical parameters of each phase in the composite coating is simulated, and the von Mises stress and the first principal stress distribution under thermal-mechanical coupled conditions is obtained. The results show that the stress of the composite coating is significantly higher than that of the uniform coating, especially at the tip of the hard phase. Improving the morphology of the phase and passivating the acute angle can effectively alleviate the local intense stress. At the same time, the thermal-mechanical coupling stress field is closely related to the elastic modulus of bonded phase and hard phase. Mises stress and tensile stress of composite coating can be effectively controlled by adjusting the modulus of each phase. The thermal-mechanical coupling stress field simulation based on the microscopic finite element method provides a theoretical basis for the optimal design of multiphase composite coatings under high temperature friction and wear conditions.

Research on the contact fatigue failure of thermal sprayed coating based on infrared thermography

Exploring thermal dynamics and porosity of cold-sprayed Ti-6Al-4V coatings on Al6061-T6 substrates: A pulsed thermography and numerical modeling approach

Study on Microstructure and Thermal Fatigue of FeMnCrAl/WC Coatings

Rolling Contact Fatigue Behavior of Thermal-Sprayed Coating: A Review

High-Temperature Wear Behavior and Mechanisms of Self-Healing NiCrAlY-Cr3C2-Ti2SnC Coating Prepared by Atmospheric Plasma Spraying

Cross-Sectional Residual Stresses in Thermal Spray Coatings Measured by Moiré Interferometry and Nanoindentation Technique

Interface Strengthening for Thermal Sprayed WC-10Co4Cr Coating Subjected to Pulsed Magnetic Treatment

Experimental Study of High Temperature Failure Behavior of Thermal Barrier Coating Based on 3D Digital Image Correlation of Single camera

Calculation and Analytical Prediction of Coating Wear during Tribological Tests Based on Models of Contact Fatigue Failure

Microstructure and Properties of Al2O3-13wt.%TiO2-Reinforced CoCrFeMnNi High-Entropy Alloy Composite Coatings Prepared by Plasma Spraying

Engineering Relationships for Computational and Analytical Prediction of Coating Wear during Tribological Tests

Atmospheric plasma sprayed thick thermal barrier coatings: Microstructure, thermal shock behaviors and failure mechanism

Thermal Conductivity Prediction in Air Plasma Sprayed Thermal Barrier Coatings Containing Multifarious Defects

The Inspection Of The Sliding Surface And Subsurface Of Plasma-Sprayed Ceramic Coatings Using Scanning Acoustic Microscopy

Investigation of temperature field for the in-situ fabrication of particle-reinforced alumina ceramics coating via laser induction

Elevated-temperature wear behavior and mechanisms of APS-sprayed Al 0.6 TiCrFeCoNi high entropy alloy coating

Estimation of fatigue life of TiN coatings using cyclic micro-impact testing

Simulation of High Temperature Friction Stress Field of Multiphase Composite Coating Based on Crystal Microscopic Finite Element Method

The Analysis of the Friction and Wear Mechanisms of Plasma-Sprayed Ceramic Coatings at 450 °C

The comparative study of thermal fatigue behavior of laser deep penetration spot cladding coating and brush plating Ni–W–Co coating