Abstract:The process of electrolytic production of Al–Y and Al–Sc alloys in an electrolyte based on potassium cryolite KF–NaF(10 wt %)–AlF3 with a cryolite ratio (CR) of 1.5, containing Al2O3, Sc2O3, or Y2O3 oxides, in a cell with vertical electrodes has been studied. The Fe–Ni–Cu alloy served as an inert anode. The wetted cathode was a graphite plate coated with the aluminum diboride. The electrolysis was carried out at a cathode current density of 0.2 A/cm2 and a temperature of 830°C. The Al2O3 mass was calculated based on the value of the current efficiency of 60%. The Sc2O3 additive was introduced into the melt in an amount of 1 wt %. The mass of the Y2O3 additive was chosen based on its solubility in the melt under study. For this, the influence of Y2O3 additives on the liquidus temperature of the quasi-binary mixture [KF–NaF(10 wt %)–AlF3 (KO = 1.5)]–Y2O3 was determined and it was found that, in contrast to Sc2O3 additives, which lower the liquidus temperature of the cryolite melt, small additions of Y2O3 lead to its sharp increase. It has been found that the efficiency of the electrolytic reduction of Y2O3 is 10 times higher than that of the aluminothermic reduction. Other things being equal, the efficiency of the electrolytic reduction of Y2O3 is higher than that of Sc2O3. Alloys Al–Y and Al–Sc with a REM content of 0.6 wt % have been obtained. However, the time to reach the maximum recovery of yttrium significantly exceeds the time to recover scandium. Metallographic studies of the obtained alloys indicated the presence of Al3Sc and Al2Y intermetallic compounds. A conclusion is made about the fundamental possibility of low-temperature electrolytic production of Al-REM alloys in cryolite melts based on potassium cryolite in vertical cells with an inert metal anode and a wettable cathode.

Metallothermic Al-Sc Co-Reduction by Vacuum Induction Melting Using Ca

Effects of Sc on the Vacancy and Solute Behaviours in Aluminium

Principles for Creating Aluminum-Based Alloys Sparingly Alloyed with Scandium

Effect of a Small Addition of Scandium on the Phase Composition and Properties of Wrought Al–Cu–Er–Mg–Mn–Zr Alloy

Study on Technological Test of Preparation of Al-Mg-Sc-bearing Master Alloy by Aluminum-magnesium Thermal Reduction on Anhydrous Scandium Chloride Molten Salt

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Selective Scandium (Sc) Extraction from Bauxite Residue (Red Mud) Obtained by Alkali Fusion-Leaching Method

Research on High-Pressure Hydrochloric Acid Leaching of Scandium, Aluminum and Other Valuable Components from the Non-Magnetic Tailings Obtained from Red Mud after Iron Removal

Extraction of Scandium and Iron from Red Mud

Effect of rare-earth Sc on the interface microstructure and mechanical properties of Al/steel bimetallic composites prepared by liquid–solid casting

Value Extraction from Ferrochrome Slag: A Thermochemical Equilibrium Calculation and Experimental Approach

Aluminothermic Reduction of CeO2: Mechanism of an Economical Route to Aluminum-Cerium Alloys

Effects of scandium addition on microstructure, mechanical and thermal properties of cast Be-Al alloy

Selective extraction of scandium from bauxite residue (red mud) utilizing iron sulfate roasting followed by water leaching

Microstructure and mechanical properties of as casted Al-Si-Sc-Ce alloys prepared by molten salt electrolysis with varied cooling rate

Processing of Al-Sc aluminum alloy using SLM technology

Efficient Selective Extraction of Scandium from Red Mud

LOW-TEMPERATURE ELECTROLYTIC PRODUCTION OF Al-REM ALLOYS IN CRYOLITE MELTS

The Effect of Scandium on the Structure, Microstructure and Superconductivity of Equimolar Sc-Hf-Nb-Ta-Ti-Zr Refractory High-Entropy Alloys

Morphology evolution and growth mechanism of primary Al3Sc and eutectic Al3Sc in Al-Sc alloys

Innovative Process for Strategic Metal Recovery from Electric Arc Furnace Slag by Alkaline Leaching