Abstract:The present study investigated influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties at both room and elevated temperatures of Al–7Mg–Sc alloys processed by hard-plate rolling (HPR). Bimodal grain structures were obtained in HPRed Al–7Mg–Sc alloys where ultrafine/fine grains decreased in size and increased in amount with increasing volume fraction of Al3Sc precipitates. The formation and evolution of bimodal grain structure are associated with (i) the different stability of various-orientated grains, and (ii) the volume fraction of Al3Sc precipitates. Ultrafine/fine (sub) grains form preferentially along grain boundaries (GBs) of <001>//normal direction (ND)- and <111>//ND-oriented coarse grains during HPR. In contrast, the <101>//ND-oriented coarse grains show relatively high stability nearly without subdivision. Furthermore, increased volume fraction of Al3Sc precipitates in Al–7Mg–0.4Sc promotes dislocation accumulation, favoring recrystallization nucleation, and meanwhile restricts grain growth, which results in more and refined ultrafine/fine grains. Thereby, the refined grain structure and increased volume fraction of Al3Sc precipitates in the Al–7Mg–0.4Sc alloy contribute to improved room-temperature yield strength (YS) and elongation, i.e. ~482 MPa and ~8%, which is much higher than that of ~420 MPa and ~4% in the binary Al–7Mg alloy. Meanwhile, Al–7Mg–0.4Sc exhibited higher hardness when annealed at 150–300 °C and also higher YS when subjected to a tensile test at ≤ 200 °C due to the more stabilized grain structure pinned by dispersed Al3Sc and additional strengthening effect from Al3Sc precipitates. Nevertheless, when subjected to a tensile test at ≥ 250 °C, the Al–7Mg–0.4Sc alloy exhibited much lower YS than binary Al–7Mg. The transition could be explained by more favored grain boundary sliding (GBS) and great dislocation loss, due to the easier occurrence of dynamic recrystallization (DRX) in Al–7Mg–0.4Sc during tensile test at elevated temperatures.

Effects of scandium addition on microstructure, mechanical and thermal properties of cast Be-Al alloy

Effects of Sc on the Vacancy and Solute Behaviours in Aluminium

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

Effect of Sc on Al3Fe phase and mechanical properties of as-cast AA5052 aluminum alloy

Effect of a Small Addition of Scandium on the Phase Composition and Properties of Wrought Al–Cu–Er–Mg–Mn–Zr Alloy

Effects of Sc addition on microstructure, phase evolution and mechanical properties of Al0.2CoCrFeNi high-entropy alloys

Influence of minor Sc additions on grain refinement and microstructure characteristics of a high Zn-containing Al-Zn-Mg-Cu-Zr alloy

Influence of the interaction between Si and Sc on the microstructure and tensile properties of as casted Al-Si-Sc alloys

Influence of scandium addition on microstructure and mechanical properties in nickel-based superalloys: An integrated multiscale modeling and experimental approach

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Effect of rare-earth Sc on the interface microstructure and mechanical properties of Al/steel bimetallic composites prepared by liquid–solid casting

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Effect of trace amounts of added Sc on microstructure and mechanical properties of 2055 aluminum alloy

Study on Sc Microalloying and Strengthening Mechanism of Al-Mg Alloy

Effect mechanism of Sc addition and T6 heat treatment on precipitated phase and mechanical properties of Al‐Cu‐Mn alloy

Effect of minor Sc additions on precipitation and mechanical properties of a new Al-Cu-Li alloy under T8 temper

Tailoring thermal conductivity and microstructure of Al–Fe alloys by addition of Sc 2 O 3 and variable cooling rates

Influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties of Al–Mg–Sc alloys processed by hard-plate rolling

Effect of Sc on the Microstructure and Properties of 7056 Aluminum Alloy