Abstract:It is widely recognized that the scandium addition to aluminum alloys is an effective way to improve the comprehensive properties. To the present, researchers are concentrated on Al-Mg alloys, for multicomponent Al-Zn-Mg-Cu alloy, the microscopic characterization of the alloy heat treatment has gained a high level of research interest. However, researches on the evolution of precipitate microstructure in controlled plastic deformation combined with the role played by Sc have received scant attention. In the present paper, a micro-alloyed Al-Zn-Mg-Cu-Sc-Zr alloy was prepared by adding 0.2% scandium. Based on mastering the two-stage homogenization treatment in the early stage, the alloy was subjected to equal channel angular extrusion deformation, and subsequently the microstructure, dislocation evolution and precipitation behavior were observed. It is revealed that after second pass deformation, the grains in the deformation-prone zone are obviously shortened by 31% on average along the cross-section direction, compared with the first pass. Following two passes deformation, Al 3 (Sc, Zr), Al 3 Zr and MgZn 2Â phases are formed within grains, inhibiting grain coarsening and recrystallization during deformation. With the introduction of plastic deformation, it is analyzed that the shadow lines with different depths and stacking faults with different structures in the interior of the phase. Also, the overall proportion of the recrystallized structure and substructure of the alloy increases with the increasing deformation. In addition, after secondary deformation, the scandium rich compounds at the trigeminal grain boundary are reduced, while the zirconium rich compounds are significantly increased. Therefore, the different diffusivity of Sc/Zr elements and the combined effect of controlled thermal deformation can be considered to prepare the Al 3 Sc (Al 3 Zr) with core-shell structure in the later stage.

Effect of a Small Addition of Scandium on the Phase Composition and Properties of Wrought Al–Cu–Er–Mg–Mn–Zr Alloy

Influence of minor Sc additions on grain refinement and microstructure characteristics of a high Zn-containing Al-Zn-Mg-Cu-Zr alloy

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys

Influence of Sc Content on the Microstructure and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Effects of scandium addition on microstructure, mechanical and thermal properties of cast Be-Al alloy

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Microstructure and Mechanical Properties of Al–Si–Mg–Cu–Ti Alloy with Trace Amounts of Scandium

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Effect of Sc content on microstructure characteristics and evolution of W phase in Al–Cu–Li alloys under as-cast and homogenization conditions

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

The Effect of Grain Refinement and Precipitation Strengthening Induced by Sc or Er Alloying on the Mechanical Properties of Cast Al-Li-Cu-Mg Alloys at Elevated Temperatures

Microstructures and Properties Evolution of Spray-Deposited Al-Zn-Mg-Cu-Zr Alloys with Scandium Addition

Influence of Sc Addition on Precipitation Behavior and Properties of Al-Cu-Mg Alloy

Effect of Chromium on Microstructure and Mechanical Properties of Al–Cu–Er–Zr Alloy

Influence of Sc on microstructure and mechanical properties of Al–Si–Mg–Cu–Zr alloy

Effect of Sc on Al3Fe phase and mechanical properties of as-cast AA5052 aluminum alloy

Plastic Deformation and Precipitation Characterization of Al-Zn-Mg-Cu Alloy Micro-Alloyed with Sc

Principles for Creating Aluminum-Based Alloys Sparingly Alloyed with Scandium

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

Effect of Sc/Zr ratio on the microstructure and mechanical properties of new type of Al–Zn–Mg–Sc–Zr alloys