Abstract:In this study, Al-20 wt% Mg 2 Si composites were prepared using an in situ endogenous process method. Various amounts of Sc were added to the composites, and a heat treatment process was employed to optimize the microstructures of the materials and enhance the overall properties of the composites. The study results indicate that the addition of Sc has a significant positive effect on both the microstructure and mechanical properties of Al-20 wt% Mg 2 Si composites. The inclusion of Sc leads to a more regular and uniformly distributed morphology of the primary Mg 2 Si phase, accompanied by a significant reduction in grain size. Particularly, when the Sc content is 0.3 wt%, the composite exhibits the most notable grain refinement effect, resulting in the best mechanical performance. The tensile strength reaches 152.7 MPa, the hardness measures 92.9 HV and the elongation is 2.82%. Through the heat treatment process, the morphology and distribution of the initial Mg 2 Si phase in the composites were optimized, resulting in significant improvements in both the morphology and distribution of the initial Mg 2 Si phase and the eutectic structure. Consequently, the tensile strength increased to 204.3 MPa, the hardness reached 117.8 HV, and the elongation improved to 3.72%. Finite element simulation was employed to model the tensile behavior of real microstructures of Al-20 wt% Mg 2 Si-0.3 wt% Sc composite in both as-cast and heat-treated conditions. The simulation results demonstrate good agreement with experiment. The fracture modes observed in both cases involve interfacial debonding and intergranular fracture. The simulation effectively showed the deformation process and stress distribution during tensile fracture. Moreover, the heat-treated model exhibits a higher load on the particles compared to the as-cast state. This finding provides evidence that the overall properties of Al-Mg 2 Si composites are enhanced following the heat treatment process.

Studying the Effect of Small Additives of Sc and Zr on the Microstructure of Al–Mg–Si Alloy with Excess Silicon during Multi-Step Heat Treatment

The influence of thermal treatment on microstructure and mechanical properties of the Si-rich Al–Mg–Si–Sc–Zr alloy

Influence of Sc on microstructure and mechanical properties of Al–Si–Mg–Cu–Zr alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Effects of Zr,Ti and Sc Additions on the Microstructure and Mechanical Properties of Al-0.4Cu-0.14Si-0.05Mg-0.2Fe Alloys

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Effect of Sc Addition and Heat Treatment on the Fracture Behavior of Al-20%Mg2Si Composites: Experiments and Finite Element Simulations

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys

Influence of minor Sc additions on grain refinement and microstructure characteristics of a high Zn-containing Al-Zn-Mg-Cu-Zr alloy

Effects of Mg and Sc Additions on the Microstructure, Mechanical Properties, and Thermal Stability of a Cast Al-2Li-2Cu-0.2Zr Alloy after Thermal Exposure

Enhancing properties of Al-Zn-Mg-Cu alloy through microalloying and heat treatment

Study of the Influence of Zirconium, Titanium and Strontium on the Properties and Microstructure of AlSi7Mg0.3Cu0.5 Alloy

Effect of Si addition on the precipitation and mechanical/electrical properties of dilute Al-Zr-Sc alloys

Microstructure and Mechanical Properties of Al–Si–Mg–Cu–Ti Alloy with Trace Amounts of Scandium

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

Effect of Step Quenching and Zr Addition on the Microstructure and Mechanical Properties of Al-Mg-Si Alloy

Effect of a Small Addition of Scandium on the Phase Composition and Properties of Wrought Al–Cu–Er–Mg–Mn–Zr Alloy

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

Heat treatment Effect of Mg-5Sn-3Zn-1Mn Alloy with different Silicon addition

Effect of Sc Microalloying Addition on Microstructure and Mechanical Properties of As-Cast Al–12Si Alloy

Study on microstructure and properties of Mg-Al-Si-Ca alloy by heat treatment