Abstract:Introduction. The practical significance of non-stoichiometric titanium carbides TiCх in various fields of technology and in medicine is expanding. In this regard, it is important to investigate both methods of obtaining titanium carbide powder and its properties in a wide range of stoichiometry. One of the effective ways to influence the physical and mechanical properties of powder systems is its mechanical treatment. Under shock-shear action, which is realized during processing in a ball mill, mechanical energy is transferred to the powder system, as a result of which it is ground, centers with increased activity on newly formed surfaces are formed; phase transformations, crystal lattice deformation, amorphization, formation of defects, etc. are possible. The aim of this work is to study the effect of low-energy mechanical treatment in a ball mill on the structure, phase composition and parameters of the fine crystal structure of non-stoichiometric titanium carbide powder obtained by reduction of titanium oxide with carbon and calcium. Materials and methods. Powder of titanium carbide TiC, obtained by calcium carbonization of titanium oxide was investigated. The powder was treated in a drum type ball mill. The structure of the powders before and after treatment was studied using the Philips SEM 515 scanning electron microscope. The specific surface area was determined by the BET method. The phase composition and parameters of the fine crystal structure of powder materials were investigated by X-ray analyzes. Results and discussion. It was established that an increase of the time of mechanical treatment in a ball mill of a non-stoichiometric titanium carbide powder TiC0.7 leads to an increase in the specific surface area of the powder from 0.6 to 3.4 m2 / g, and the average particle size calculated from it decreases from 2 μm to 360 nm. It is shown that in the process of treatment of the non-stoichiometric titanium carbide TiC0.7 powder, its structural phase state changes. Powder particles consist of two structural components with different atomic ratio of carbon to titanium: TiC0.65 and TiC0.48. Mechanical treatment of titanium carbide powder leads to a decrease in the microstresses of the TiCx crystal lattice and the size of coherently diffracting domains (CDD) from 55 to 30 nm for the TiC0.48 phase. For the TiC0.65 phase, with an increase in the duration of mechanical treatment, as well as for TiC0.48, the size of CDD decreases, and the level of microdistortions of the crystal lattice increases. This indicates that in the process of mechanical treatment, not only the grinding of powder particles occurs, but also an increase in its defects.

Effects of process parameters on morphologies of titanium carbide powder by thermal plasma treatment

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Investigation of TiC formation during ball-milling of elemental titanium and carbon

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Effects of Induction Plasma Spheroidization on Properties of Yttria-Stabilized Zirconia Powders for Thermal Barrier Coating Applications

Low energy mechanical treatment of non-stoichiometric titanium carbide powder

Effect of processing parameters on microstructure and properties of spherical WC-Co powder by plasma spheroidization

Refinement of TiB2 Powders with High-speed Planetary Mill and Its Effect on TiB2 Sinterability

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Modification and control of TiC morphology by various ways in arc melted TiC/Ti-6Al-4V composites

Effects of TiC Addition on Microstructures, Mechanical Properties and Fracture Behaviors of Porous Titanium Carbide Ceramics

Effects of Treatment Process and Nano-Additives on the Microstructure and Properties of Al2O3-TiO2 Nanocomposite Powders Used for Plasma Spraying

Densification and Mechanical Properties of Tic by Sps-Effects of Holding Time, Sintering Temperature and Pressure Condition

Effects of carbon addition on the microstructure and mechanical property of in-situ reinforced TiAl matrix composite powders produced by plasma rotating electrode process

Synthesis and Sintering of Tungsten and Titanium Carbide: A Parametric Study

Effect of nano-TiC addition on sinterability and mechanical properties of TiC high temperature ceramics

Effects of Processing Parameters on the Surface Quality of Directionally Solidified Titanium Alloy Slab with Cold Crucible

The spark plasma sintering of fine grained TiCN-Mo-Ni cermets

The Effects of Induction Plasma Spheroidization on the Properties of Yttrium-Stabilized Zirconia Powders and the Performance of Corresponding Thermal Barrier Coatings for Gas Turbine Engine Applications

Effect of pre-solid solution treatment of secondary carbides on the microstructure and mechanical properties of Ti(C,N)-based cermets

Effect of spraying ceramic powder pore structure on thermophysical properties of plasma-sprayed thermal barrier coatings