Electrochemical Impedance Spectroscopy to Investigate Electroplating of Metals

Masayuki Itagaki,Yusuke Ito,Yoshinao Hoshi,Isao Shitanda

DOI: https://doi.org/10.1149/ma2013-01/28/1049

2013-03-08

ECS Meeting Abstracts

Abstract:Abstract not Available.

What problem does this paper attempt to address?

Electrochemical impedance spectroscopy of metals covered with a thin electrolyte layer

A. Nishikata,Y. Ichihara,T. Tsuru

DOI: https://doi.org/10.1016/0013-4686(95)00438-6

IF: 6.6

1996-05-01

Electrochimica Acta

Abstract:The impedance behavior of metals covered with a thin electrolyte layer has been investigated. A transmission line (TML) circuit type behavior, which was attributed to an uneven current distribution profile over a working electrode, was observed in a wider frequency range as the thickness and the concentration of the electrolyte were decreased. It was found from the theoretical analysis based on the TML model that the current distribution profile becomes uniform at least in the low frequency limit when the phase shift θ goes further than −45 ° on a plot of θ vs. log f(f = frequency). In such a condition, an accurate corrosion rate can be determined from the obtained polarization resistance Rp. The EIS has been applied to investigate the dependence of the atmospheric corrosion of stainless steel and of copper on the thickness of the electrolyte layer. The corrosion rate of stainless steel covered with an NaCl solution layer was independent of the thickness at least down to the thickness of 10 μm because it was controlled by the anodic process. The corrosion rate of copper covered with a neutral Na2SO4 solution was independent of the thickness at least down to 10 μm, whereas the copper covered with an acidic solution of pH 3 showed a maximum at a thickness of several tens of micrometers.

electrochemistry
Recent Progress in the Studies of Electrochemical Interfaces by Surface Plasmon Resonance Spectroscopy and Microscopy

Andy Chieng,Michelle Chiang,Kraisarun Triloges,Megan Chang,Yixian Wang

DOI: https://doi.org/10.1016/j.coelec.2018.11.002

IF: 8.5

2018-01-01

Current Opinion in Electrochemistry

Abstract:Surface plasmon resonance (SPR) is a label-free spectroscopic technique that is highly sensitive to various surface reactions. Incorporating SPR into electrochemical measurements has emerged as a powerful method to study both faradaic and non-faradaic processes. SPR microscopy (SPRM) integrates an optical microscope into SPR detection, which further offers high throughput detection and spatially resolved information at an electrode surface and thus, has attracted attention especially in single entity electrochemical studies. In this review, the progress in the studies of electrochemical interfaces by SPR and SPRM during the past two years will be discussed.
Electrochemical Analysis of Cathode in TSV Copper Electroplating

Haiyong Cao,Xue Feng,Qi Sun,Wei Luo,Huiqin Ling,Jiangyan Sun,Ming Li

DOI: https://doi.org/10.1109/icsj.2012.6523399

2012-01-01

Abstract:In TSV copper electroplating, the most important is to form the “bottom up” deposition. In order to achieve this kind of super-filling, additive in the electroplating bath need to play its own role at the respective position. Accelerator adsorb at the bottom of the via to accelerate the deposition of copper while suppressor mostly adsorb at the top of the via to inhibit the deposition. Therefore, vias could be supper-filled without any void. In this paper, bis(3-sulfopropyl) disulfide (SPS) and polyethylene glycol (PEG) were used as accelerator and suppressor respectively. The supper-filling mechanism and the competitive adsorption of SPS and PEG were being researched by means of linear sweep voltammetry (LSV) and cyclic voltammogram (CV). The electrochemical analysis and the experimental plating are closely related.
Electrochemical Impedance Spectroscopy (EIS): A Review Study of Basic Aspects of the Corrosion Mechanism Applied to Steels

Héctor Herrera Hernández,Adriana M. Ruiz Reynoso,Juan C. Trinidad González,Carlos O. González Morán,José G. Miranda Hernández,Araceli Mandujano Ruiz,Jorge Morales Hernández,Ricardo Orozco Cruz

DOI: https://doi.org/10.5772/intechopen.94470

2020-12-16

Abstract:AC impedance measurements have been applied for over twenty years in electrochemistry and physics to investigate the electrical properties of conductive materials and their interfaces using an external electrical impulse (VOLTAGE, V or CURRENT, I) as driving force. Furthermore, its application has recently appeared to be destined in the Biotechnology field as an effective tool for rapid microbiologic diagnosis of living organism in situ. However, there is no doubt that the electrochemical impedance spectroscopy (EIS) is still one of the most useful techniques around the world for metal corrosion control and its monitoring. Corrosion has long been recognized as one of the most expensive stumbling blocks that concern many industries and government agencies, because it is a steel destructive phenomenon that occurs due to the chemical interaction with aqueous environments and takes place at the interface between metal and electrolyte producing an electrical charge transfer or ion diffusion process. Consequently, it is experimentally possible to determine through the EIS technique the mechanism and control that kinectics of corrosion reactions encounter. First, EIS data is collected through a potentiostat/galvanostat apparatus. After, it is fitted to a mathematical model (i.e. an equivalent electrical circuit, EEC) for its interpretation and analysis, fundamentally seeking a meaningful physical interpretation. Finally, this review reports some basic aspects of the corrosion mechanism applied to steels through the experimental EIS response using Nyquist or Bode plots. Examples are given for different applied electrochemical impedance cases in which steel is under study intentionally exposed to a corrosive aqueous solution by applying a sinusoidal potential at various test conditions.
Development on Electrochemical Impedance Spectroscopy Technology in Metal Corrosion and Coating Anticorrosion

Yaohui LV,Yuxin LIU,Dongyu HE,Xi CHEN,Xiaoting LIU,Wenyu WANG,Yanfei HUANG,Qing CHANG

DOI: https://doi.org/10.3969/j.issn.1001-3849.2018.06.006

2018-01-01

Abstract:The application of Electrochemical Impedance Spectroscopy (EIS) in metal corrosion and protection was described in this paper.The anti-corrosion performance and corrosion mechanism were discussed respectively for metal corrosion,organic coatings,inorganic nano-coatings,metal coatings and the organic coating in simulated deep-sea environment through EIS technology.Finally,some problems existed in the Ac impedance AD were pointed out and the application of the EIS in corrosion science and other fields were predicted.
Electrochemical Impedance Spectroscopy Analysis on Aluminum Alloys in EXCO Solution

FH Cao,Z Zhang,JX Su,JQ Zhang

DOI: https://doi.org/10.1002/maco.200403844

2005-01-01

Materials and Corrosion

Abstract:Electrochemical impedance spectroscopy (EIS) of Al‐Zn‐Mg‐Cu alloy in EXCO solution has been investigated. The results show that the impedance spectroscopy of the investigated electrode consists of two capacitive loops in the high and middle frequency domain respectively and an inductive loop in the low frequency domain at the first 30 h of immersion; the inductive arc disappears between 30 h and 60 h while it takes on at the low frequency domain at the last 36 h of the immersion time. A model based on the corrosion mechanism of the aluminum alloy and corroding morphology was proposed and applied to analyze the EIS results.
Electrochemical Impedance Monitoring of Copper Damascene Chemistries

Delia Nieto Sanzb,Hung-Ming Chen,S. J. Parulekar,A. Zduneka

Abstract:This paper describes electrochemical impedance spectroscopy (EIS) measurements performed on copper damascene plating chemistries during non-production plating experiments and on process tool baths during copper metallization to characterize changes in the plating bath condition. The results show that the shape of the impedance scan is sensitive to changes in the steady state of the bath chemistry, bleed/feed operation, and process perturbations, and may be an indicator of the overall bath quality. Further development of this method, as an online monitor to track the overall bath quality and its incorporation into a copper bath management and delivery system, are also discussed. Introduction The promising electrical properties and capability to deposit copper into submicron features by superconformal deposition have brought copper electroplating technology into the mainstream of the semiconductor metallization process. However, the ability to perform superconformal deposition of copper in vias and trenches depends strongly on specific organic additives to the copper sulfate/sulfuric acid-based electroplating bath. Achieving a defect-free deposition requires a precise maintenance of the concentrations of additives and additive byproducts. Monitoring or controlling these is therefore crucial to guaranteeing the properties of the copper deposit. The roles of bath ageing and additive degradation are of considerable interest since these can affect the quality of the copper deposit and ultimately influence copper bath chemical management schemes [1]. Additionally, changes in the overall bath quality influenced by manufacturing conditions, additive degradation, and byproduct accumulation, can profoundly affect the copper deposit and these are not presently controlled. State-of-the art copper interconnect plating tools use online monitoring to quantify bath component concentrations to achieve tighter bath control. Presently, bath quality is maintained by bleeding part of the solution about 10% each day. A more quantitative determination of bath quality would enable out-of-spec bath conditions to be readily measured, identified and controlled, and more accurate preventative maintenance performed. While quantifying bath ageing and measuring byproducts has been reported, optimization of bath quality management remains difficult, partly due to the proprietary nature of copper bath formulations [2-4]. Electrochemical impedance spectroscopy (EIS) was proposed as a possible method for following bath quality during wafer processing [1]. Laboratory experiments involving simulated bath ageing revealed that the impedance technique can track copper bath ageing during and after plating [1]. Furthermore, these results appeared to correlate well with deposit morphology and thus maybe a reliable indicator of the overall quality of the bath during plating operation [5]. EIS measurements were also made on plating bath solutions taken from production copper deposition tools at a semiconductor manufacturing fab [6,7]. EIS was able to distinguish between different bath compositions, as well as between different process perturbations. In this paper, impedance measurements were made on copper damascene plating chemistries during non-production plating experiments and on additional process tool baths during copper metallization. The non-production plating experiments allowed out-of-spec bath conditions with recovery back to a steady state to be characterized without manufacturing production constraints and the risk of wafer loss. The production tests were performed to further demonstrate that EIS can detect differences in production bath chemistries including changes attributable to process perturbations and maintenance functions.

Materials Science,Engineering,Chemistry
Electrochemical Impedance Studies for Intergranular Corrosion of Super 304H Stainless Steel

Y. J. Ren,Y. Q. Chen,J. Chen,W. Li,C. L. Zhang

2016-01-01

Abstract:At high temperatures, Super 304H stainless steel (SS) (UNS S30432) usually suffers intergranular corrosion. Electrochemical methods, including electrochemical impedance spectroscopy (EIS) and electrochemical potentiokinetic reactivation (EPR), were employed to investigate the intergranular corrosion of sensitized Super 304H austenitic SS for different lengths of time at 650 degrees C. The EIS results showed that the charge transfer resistance, R-t, and corrosion product resistance, R-f, decreased significantly with increased sensitization time, indicating that susceptibility to intergranular corrosion increased. These results coincided with those of EPR.
Application of EIS to localized corrosion

R. Oltra,M. Keddam

DOI: https://doi.org/10.1016/0013-4686(90)80018-j

IF: 6.6

1990-10-01

Electrochimica Acta

Abstract:The possibilities and limitations of Electrochemical Impedance Spectroscopy (EIS) for localized corrosion studies are reviewed and assessed on the basis of modelling and experimental data. It is shown that the main features of EIS on localized corrosion systems arise from the frequency dependence of the ac current distribution between corrosion sites and surrounding passive background. An original set-up (electronics and laser beam triggered pitting) for analysing this effect and its consequence on EIS diagrams is presented. The case of s.s.c. giving rise to transmission-line behaviour of EIS is considered separately.

electrochemistry
A Study on Corrosion Behavior of Type 304 Stainless Steel with Electrochemical Impedance Spectroscopy in High Temperature Pure Water

Katsumi Mabuchi,Masanori Sakai,Noriyuki Ohnaka

DOI: https://doi.org/10.3323/jcorr1991.43.2

1994-01-01

Abstract:Electrochemical behavior of Type 304 stainless steel and carbon steel in high temperature pure water has been studied by using an electrochemical impedance spectroscopy. Under high dissolved oxygen concentration, impedance diagram for Type 304 stainless steel and carbon steel are founded to be composed of two capacitive semicircles. Impedance response at high frequency is that of H2O/O2 redox reaction and at low frequency is that of corrosion reaction correlated to oxide film growth. Impedance frequency dispersion of Type 304 stainless steel and carbon steel are divided mainly into those of redox reactions, diffusion of an oxygen bearing ions through oxide films, and dissolution of iron using an equivalent circuit obtained by oxygen diffusion model for film growth. Variation in corrosion rates obtained by weight loss measurement are compared with variation in reciprocal of the Warburg impedance coefficient obtained by numerical analysis.Under low dissolved oxygen concentration, only impedance of H2O/H2 redox reaction was observed, because that redox reaction is independent of corrosion reaction and has high reversibility. The pure charge transfer resistance of the corrosion process of Type 304 stainless steel and carbon steel can not be obtained in high temperature water.
Electrochemical impedance spectroscopy during corrosion process of 8090 Al-Li alloy in EXCO solution

Jinfeng Li,Ziqiao Zheng,ChengYu Tan,Shichen Li,Zhao Zhang,Jianqing Zhang

2004-01-01

Acta Metallurgica Sinica (English Letters)

Abstract:The corrosion behavior and electrochemical impedance spectroscopy (EIS) features of 8090 Al-Li alloys in EXCO solution were investigated, and the EIS was simulated using an equivalent circuit. At the beginning of immersion in EXCO solution, the EIS is comprised by a depressed capacitive arc at high-mediate frequency and an inductive arc at low frequency, and the inductive component decreases and disappears with immersion time. Once exfoliation or severe pitting corrosion is produced, two capacitive arcs appear in the EIS. These two capacitive arcs are originated from the two parts of the corroded alloy surface, the original flat alloy surface and the new inter-face exposed to the aggressive EXCO solution due to the exfoliation or pitting corrosion. Some corrosion development features of 8090 Al-Li alloys in EXCO solution can be obtained through simulated EIS information.
Electrochemical Impedance Spectroscopy Analysis on the Electrochemical Dissolution of Aluminum in an Alkaline Solution

HB Shao,JM Wang,Z Zhang,JQ Zhang,CN Cao

DOI: https://doi.org/10.1016/s0022-0728(03)00266-3

IF: 4.598

2003-01-01

Journal of Electroanalytical Chemistry

Abstract:The process of electrochemical dissolution of aluminum in an alkaline solution was investigated by electrochemical impedance spectroscopy (EIS). A model based on its reaction mechanism was proposed. The kinetic parameters including rate constants of each step and covering densities of intermediates were obtained. The EIS was well analyzed by this model.
Influence of Organic Coating Thickness on Electrochemical Impedance Spectroscopy Response

Amanda Suellen de Paula,Barbara Mitraud Aroeira,Lucas Henrique de Oliveira Souza,Alisson Cristian da Cruz,Michele Fedel,Brunela Pereira da Silva,Fernando Cotting

DOI: https://doi.org/10.3390/coatings14030285

IF: 3.236

2024-02-28

Coatings

Abstract:Electrochemical Impedance Spectroscopy (EIS) is a non-destructive and powerful technique for characterizing corrosion systems, allowing for the evaluation of surface reaction mechanisms, mass transport, kinetic evolution, and corrosion levels of materials. This study aims to analyze the progression of corrosion using EIS, with a focus on the influence of organic coating thickness. For this purpose, layers of high-purity epoxy paint were applied to carbon steel plates with thicknesses of 50 μm, 80 μm, and 100 μm. During the research, a direct correlation was observed between coating thickness and corrosion resistance, emphasizing the importance of identifying the optimal thickness for each type of coating. Additionally, it was found that thicker coatings may experience electrode penetration due to the tensions generated during deposition, resulting in cracks between the layers, while thinner coatings allow electrolyte penetration as they do not provide adequate protection to the base steel. Therefore, the 80 μm thickness demonstrated greater resistance to corrosion compared to the other tested thicknesses.

materials science, multidisciplinary,physics, applied, coatings & films
An Immersion Ultrasonic Testing‐Based Research Platform for Studying Electroplating Kinetics

Yang Zirui,Chen Yunda,Fangxin Zou,Frederic B. Cegla

DOI: https://doi.org/10.1002/celc.202400164

IF: 4

2024-04-13

ChemElectroChem

Abstract:An immersion ultrasonic testing‐based technique that carries out in situ, direct monitoring of the thickness increases of electroplated layers is introduced. The technique possesses a sub‐micron measurement resolution and an experimentally proven measurement accuracy. The technique can become a new alternative for studying the kinetics of different electroplating processes. Electroplating is widely exploited in numerous application areas. Understanding the kinetics of electroplating, which is essentially a dynamic phenomenon, is crucial to making use of it appropriately in the real world. Currently, there exist a variety of research tools for studying electroplating kinetics, each with its own pros and cons. In this paper, we introduce a novel, immersion ultrasonic testing‐based technique that carries out in situ, direct monitoring of the thickness increase of an electroplated layer. Through careful design and optimization of the measurement setup and the signal processing protocol, the measurement resolution of the technique was able to reach a sub‐micron level. Via a number of demonstrative zinc plating experiments that were performed under different conditions, the measurement accuracy of the technique was thoroughly validated by a number of independent methods. All in all, the technique can become a promising alternative tool for studying the kinetics of different electroplating processes, supplementing the existing toolbox with the capability of providing a new class of information.

electrochemistry
Effect of Internal Resistance of Reference Electrode System on Electrochemical Impedance Spectroscopy

MC Li,CL Zeng,HC Lin,CN Cao

2001-01-01

Abstract:Electrochemical impedance spectra of 316 stainless steel in NaCl solutions with different concentration, which were measured by using reference electrode systems with different internal resistance, were presented. The results showed that the large internal resistance of reference electrode system induced capacitive high frequency phase shifting impedance measurement. It was also found that high frequency phases shifts were reduced with the decrease of solution resistance and the internal resistance of reference electrode system.
Electrochemical Impedance Spectroscopy Integrated with Environmental Transmission Electron Microscopy

Zhongtao Ma,Waynah Lou Dacayan,Christodoulos Chatzichristodoulou,Kristian Speranza Mølhave,Francesco Maria Chiabrera,Wenjing Zhang,Søren Bredmose Simonsen

DOI: https://doi.org/10.1002/smtd.202201713

IF: 12.4

Small Methods

Abstract:The concept of combining electrical impedance spectroscopy (EIS) with environmental transmission electron microscopy (ETEM) is demonstrated by testing a specially designed micro gadolinia-doped ceria (CGO) sample in reactive gasses (O2 and H2 /H2 O), at elevated temperatures (room temperature-800 °C) and with applied electrical potentials. The EIS-TEM method provides structural and compositional information with direct correlation to the electrochemical performance. It is demonstrated that reliable EIS measurements can be achieved in the TEM for a sample with nanoscale dimensions. Specifically, the ionic and electronic conductivity, the surface exchange resistivity, and the volume-specific chemical capacitance are in good agreement with results from more standardized electrochemical tests on macroscopic samples. CGO is chosen as a test material due to its relevance for solid oxide electrochemical reactions where its electrochemical performance depends on temperature and gas environment. As expected, the results show increased conductivity and lower surface exchange resistance in H2 /H2 O gas mixtures where the oxygen partial pressure is low compared to experiments in pure O2 . The developed EIS-TEM platform is an important tool in promoting the understanding of nanoscale processes for green energy technologies, e.g., solid oxide electrolysis/fuel cells, batteries, thermoelectric devices, etc.
Applications of Impedance Spectroscopy

N. Bonanos,B. C. H. Steele,E. P. Butler,J. Ross Macdonald,William B. Johnson,Wayne L. Worrell,Gunnar A. Niklasson,Sara Malmgren,Maria Strømme,S. K. Sundaram,Michael C. H. McKubre,Digby D. Macdonald,George R. Engelhardt,Evgenij Barsoukov,Brian. E. Conway,Wendy. G. Pell,Norbert Wagner,C. M. Roland,Robert S. Eisenberg

DOI: https://doi.org/10.1002/9781119381860.ch4

2018-03-25

Abstract:A wide range of materials can be usefully characterized by impedance spectroscopy (IS), namely, electrical and structural ceramics, magnetic ferrites, semiconductors, membranes, polymeric materials, and protective paint films. The measurement techniques used to characterize materials are generally simpler than those used for electrode processes. This chapter first discusses microstructural models describing grains and grain boundaries of differing phase composition, suspensions of one phase within another, and porosity. It then gives examples of the combined use of IS and electron microscopy. The chapter then discusses the models that have been proposed for describing the conductive‐system dispersive responses. It then presents examples of several different applications of IS. Four different devices have been chosen: solid electrolyte chemical sensors (SECSs), secondary batteries, photoelectrochemical devices, and semiconductor‐insulator‐electrolyte sensors. The chapter further reviews the application of IS to the study of corrosion phenomena.
Visualization of EIS at large potential range - new insights

Ivan Napoleão Bastos,Marcos Paulo Moura Carvalho,Ricardo Fabbri,Ricardo Pereira Nogueira

DOI: https://doi.org/10.48550/arXiv.1310.1629

2013-10-06

Materials Science

Abstract:Electrochemical Impedance Spectroscopy (EIS) is an experimental technique largely used in electrochemistry and corrosion studies. However, almost all published papers have just measured the EIS at the corrosion potential, especially for corrosion purposes. This fact limits the capability of the technique. In this paper, a Scilab software was developed which allows the visualization of multiple EIS diagrams regarding the potential, exposure time or experiment run. This procedure was applied to austenitic stainless steels in two electrolytes from cathodic to anodic potentials. The EIS maps with two- or three- dimensions were very useful to depict the evolution of the surface with respect to the large range of applied potential. Some results are shown to highlight the usefulness of this approach as a complementary technique to the DC test performed at a given potential range.
Impedance investigation of the anodic iron dissolution in perchloric acid solution

Houyi Ma,Guiqiu Li,Shenhao Chen,Shiyong Zhao,Xiaoliang Cheng

DOI: https://doi.org/10.1016/S0010-938X(01)00145-7

IF: 7.72

2002-01-01

Corrosion Science

Abstract:The anodic iron dissolution in 0.5 moldm−3 perchloric acid (HClO4) was investigated by the electrochemical impedance spectroscopy, the potentiodynamic sweep and the scanning electron microscopy measurements. The anodic polarization behavior of iron in HClO4 solution showed that the strong current oscillations occurred in a narrow potential region, particularly the pitting corrosion was observed in the active dissolution region. These characteristics were quite different from those of iron in the sulfuric acid (H2SO4). At the potentials 82 and 132 mV more positive than the corrosion potential (−482 mV vs. SCE), the impedance spectra for the iron in HClO4 displayed two inductive arcs; however, by gradually increasing potential the lower frequency inductive arc disappeared at −300 mV at first, and then the higher frequency inductive arc changed into a capacitive arc at −250 mV. Based on the impedance display of iron at various potentials, a reaction model involving two adsorbed intermediate species was proposed, in terms of which the impedance behavior at different potentials were described. Occurrence of the pitting corrosion in active dissolution region was explained.
Electrochemical impedance study of the hematite/water interface

Kenichi Shimizu,Andrzej Lasia,Jean-François Boily

DOI: https://doi.org/10.1021/la300829c

IF: 3.9

2012-05-22

Langmuir

Abstract:Reactions taking place on hematite (α-Fe(2)O(3)) surfaces in contact with aqueous solutions are of paramount importance to environmental and technological processes. The electrochemical properties of the hematite/water interface are central to these processes and can be probed by open circuit potentials and cyclic voltammetric measurements of semiconducting electrodes. In this study, electrochemical impedance spectroscopy (EIS) was used to extract resistive and capacitive attributes of this interface on millimeter-sized single-body hematite electrodes. This was carried out by developing equivalent circuit models for impedance data collected on a semiconducting hematite specimen equilibrated in solutions of 0.1 M NaCl and NH(4)Cl at various pH values. These efforts produced distinct sets of capacitance values for the diffuse and compact layers of the interface. Diffuse layer capacitances shift in the pH 3-11 range from 2.32 to 2.50 μF·cm(-2) in NaCl and from 1.43 to 1.99 μF·cm(-2) in NH(4)Cl. Furthermore, these values reach a minimum capacitance at pH 9, near a probable point of zero charge for an undefined hematite surface exposing a variety of (hydr)oxo functional groups. Compact layer capacitances pertain to the transfer of ions (charge carriers) from the diffuse layer to surface hydroxyls and are independent of pH in NaCl, with values of 32.57 ± 0.49 μF·cm(-2)·s(-φ). However, they decrease with pH in NH(4)Cl from 33.77 at pH 3.5 to 21.02 μF·cm(-2)·s(-φ) at pH 10.6 because of the interactions of ammonium species with surface (hydr)oxo groups. Values of φ (0.71-0.73 in NaCl and 0.56-0.67 in NH(4)Cl) denote the nonideal behavior of this capacitor, which is treated here as a constant phase element. Because electrode-based techniques are generally not applicable to the commonly insulating metal (oxyhydr)oxides found in the environment, this study presents opportunities for exploring mineral/water interface chemistry by EIS studies of single-body hematite specimens.

Electrochemical Impedance Spectroscopy to Investigate Electroplating of Metals

Electrochemical impedance spectroscopy of metals covered with a thin electrolyte layer

Recent Progress in the Studies of Electrochemical Interfaces by Surface Plasmon Resonance Spectroscopy and Microscopy

Electrochemical Analysis of Cathode in TSV Copper Electroplating

Electrochemical Impedance Spectroscopy (EIS): A Review Study of Basic Aspects of the Corrosion Mechanism Applied to Steels

Development on Electrochemical Impedance Spectroscopy Technology in Metal Corrosion and Coating Anticorrosion

Electrochemical Impedance Spectroscopy Analysis on Aluminum Alloys in EXCO Solution

Electrochemical Impedance Monitoring of Copper Damascene Chemistries

Electrochemical Impedance Studies for Intergranular Corrosion of Super 304H Stainless Steel

Application of EIS to localized corrosion

A Study on Corrosion Behavior of Type 304 Stainless Steel with Electrochemical Impedance Spectroscopy in High Temperature Pure Water

Electrochemical impedance spectroscopy during corrosion process of 8090 Al-Li alloy in EXCO solution

Electrochemical Impedance Spectroscopy Analysis on the Electrochemical Dissolution of Aluminum in an Alkaline Solution

Influence of Organic Coating Thickness on Electrochemical Impedance Spectroscopy Response

An Immersion Ultrasonic Testing‐Based Research Platform for Studying Electroplating Kinetics

Effect of Internal Resistance of Reference Electrode System on Electrochemical Impedance Spectroscopy

Electrochemical Impedance Spectroscopy Integrated with Environmental Transmission Electron Microscopy

Applications of Impedance Spectroscopy

Visualization of EIS at large potential range - new insights

Impedance investigation of the anodic iron dissolution in perchloric acid solution

Electrochemical impedance study of the hematite/water interface