Abstract:To improve the mechanical properties of Ti48Al2Cr2Nb (TiAl) alloys, Ti48Al2Cr2Nb-xTa alloy specimens without metallurgical defects were obtained by a laser additive manufacturing (LAM) technique using Ti48Al2Cr2Nb/Ta mixed powders as raw materials. The effects of different Ta contents on the microstructures, phase compositions, and tensile properties of the TiAl alloys were systematically investigated, and the relationship between these properties was established. The results showed that the lamellar structure was composed of α2 (Ti3Al), γ (TiAl), and β/B2 (β ordered to B2) phases. With the increase of Ta content, the thickness of the lamellar structure increased, and the lamellar length gradually shortened. The morphology of the α2 phase changed from an ultra-fine continuous lamellar structure to a short lamellar and an equiaxed structure. On the other hand, the morphology of the γ phase changed from lamellar to an equiaxed crystal structure, while the morphology of β/B2 phase changed from ellipsoid shape to fine block to coarse block structure. When the amount of Ta added to the TiAl powders was 0 at.%, 2 at.%, and 5 at.%, respectively, the tensile strength gradually decreased with the increase of temperature, while the elongation increased. When the amount of Ta was 8 at.%, the tensile strength at room temperature dropped to the minimum (393 MPa), and the elongation reached its maximum value (21.2%). Thus, it can be concluded that the 5 at.%Ta alloy had the best comprehensive tensile properties. The maximum tensile strength of the TiAl-5 at.%Ta alloy at room temperature, 750 °C and 850 °C, was 677 MPa, 651 MPa, and 538 MPa, respectively, and the elongation was 2.0%, 2.0%, and 13%, respectively. Compared with the TiAl-0 at.%Ta alloy, the tensile strength of TiAl-5 at.%Ta at room temperature, 750 °C, and 850 °C increased by 1.66, 2.08, and 1.9 times respectively, and the elongation increased by 1.43, 1.43, and 9.29 times, respectively.

Liquid metal dealloying of titanium-tantalum (Ti-Ta) alloy to fabricate ultrafine Ta ligament structures: A comparative study in molten copper (Cu) and Cu-based alloys

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Microstructure of a Ti–50 Wt% Ta Alloy Produced Via Laser Powder Bed Fusion

Effects of Tantalum Concentration on the Microstructures and Mechanical Properties of Tungsten-Tantalum Alloys

Cold Crucible Levitation Melting of Biomedical Ti-30 wt%Ta Alloy.

Investigation on the Microstructure and Mechanical Properties of the Ti-Ta Alloy with Unmelted Ta Particles by Laser Powder Bed Fusion

[Structural characteristics and biocompatibility of a new nano-Ta-Ti alloy rod fabricated by laser melting technique]

Effects of Tantalum on the microstructure and properties of Ti-48Al-2Cr-2Nb alloy fabricated via laser additive manufacturing

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Room Temperature Deformation and Superelastic Behavior of TLM Titanium Alloy Under Different Solution Conditions

Mechanical alloying and thermal analysis of Ta–Ti alloys

Improvement on mechanical properties and corrosion resistance of titanium-tantalum alloys in-situ fabricated via selective laser melting

Effects of tantalum addition on microstructure and properties of titanium alloy fabricated by laser powder bed fusion

Ti-Ta-Cu Biocompatible Alloy System Development via Selective Laser Melting for Prosthetic Applications

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Simultaneous improvement of strength and ductility of laser additively produced Ti6Al4V by adding tantalum

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Microstructural evolution and cryogenic-normal temperature deformation behavior of the near-α titanium alloy TA15 fabricated by laser powder bed fusion

Tailoring the Ductility of Ti-6Al-4V Titanium Alloy Fabricated by Laser Power Bed Fusion at Liquid Nitrogen Temperature

Metastable microstructure evolution and grain refinement in a Low-Ta containing γ-TiAl alloy through heat treatment

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment