Abstract:A radio-frequency micro-electro-mechanical system (RF MEMS) wafer-level packaging (WLP) method using pre-patterned benzo-cyclo-butene (BCB) polymers with a high-resistivity silicon cap is proposed to achieve high bonding quality and excellent RF performance. In this process, the BCB polymer was pre-defined to form the sealing ring and bonding layer by the spin-coating and patterning of photosensitive BCB before the cavity formation. During anisotropic wet etching of the silicon wafer to generate the housing cavity, the BCB sealing ring was protected by a sputtered Cr/Au (chromium/gold) layer. The average measured thickness of the BCB layer was 5.9 mu m. In contrast to the conventional methods of spin-coating BCB after fabricating cavities, the pre-patterned BCB method presented BCB bonding layers with better quality on severe topography surfaces in terms of increased uniformity of thickness and better surface flatness. The observation of the bonded layer showed that no void or gap formed on the protruding coplanar waveguide (CPW) lines. A shear strength test was experimentally implemented as a function of the BCB widths in the range of 100-400 mu m. The average shear strength of the packaged device was higher than 21.58 MPa. A RF MEMS switch was successfully packaged using this process with a negligible impact on the microwave characteristics and a significant improvement in the lifetime from below 10 million to over 1 billion. The measured insertion loss of the packaged RF MEMS switch was 0.779 dB and the insertion loss deterioration caused by the package structure was less than 0.2 dB at 30 GHz.

Thin Film Encapsulation for RF MEMS in 5G and Modern Telecommunication Systems

Monolithic Integration of a Wafer-Level Thin-Film Encapsulated mm-Wave RF-MEMS Switch in BEOL of a 130-nm SiGe BiCMOS Technology

Enhanced Thermal Conductivity and Microwave Dielectric Properties by Mesostructural Design of Multiphase Nanocomposite

Parasitic Effects Reduction for Wafer-Level Packaging of RF-Mems

A Pre-Shaped Wafer Level Packing Strategy for Rf Mems

Ultrathin Encapsulation Strategies with Predefined Gate Dielectric Surface Area for Flexible Crystalline Silicon Nanomembrane-Based MOS Capacitors

The key technologies in silicon based microwave and RF MEMS device fabrication

Thick film hydrogen silsesquioxane planarization for passive component technology associated with electronic-photonic integrated circuits

Capacitive Diaphragm for Compartment Shielding in the Fifth-Generation Radio Frequency Systems

Crosslinked PMMA as a Low-Dimensional Dielectric Sacrificial Layer for MEMS/NEMS and Quantum Nanostructures Fabrication

A Surface Micromachining Process for Suspended RF-MEMS Applications Using Porous Silicon

Research on a 3D Encapsulation Technique for Capacitive MEMS Sensors Based on Through Silicon Via

Integrated RF MEMS/CMOS Devices

Wafer-Level Packaging Method For Rf Mems Applications Using Pre-Patterned Bcb Polymer

Integrating high-efficiency thermal channel construction and structural wave absorption design within vertically oriented SiC-coated carbon fibers/silicone resin composites

Encapsulation of Film Bulk Acoustic Resonator Filters Using A Wafer-Level Microcap Array

Design and analysis of Piezoelectric MEMS Varactor loaded on QMSIW filter for 5G Communication

Process Development of Thick Si Interposer for 2.5d Integration of Rf Mems Devices

Surface Encapsulation for Low-Loss Silicon Photonics

Simple and fast modelling of radio frequency passives in view of beyond-5G and 6G applications: case study of an RF-MEMS multi-state network described by an equivalent lumped element network

Integrating porous silicon layer backing to capacitive micromachined ultrasonic transducers (CMUT)-based linear arrays for acoustic Lamb wave attenuation