Abstract:FeCoNiCrAl0.8Cu0.5Si0.5 high-entropy alloys were fabricated using vacuum induction melting and laser deposition processes, followed by a comparison of the structural and mechanical properties of two distinct sample types. The as-cast FeCoNiCrAl0.8Cu0.5Si0.5 alloy is comprised of BCC1, BCC2, and Cr3Si phases, while the laser-deposited alloy primarily features BCC1 and BCC2 phases. Microstructural analysis revealed that the as-cast alloy exhibits a dendritic morphology with secondary dendritic arms and densely packed grains, and the laser-deposited alloy displays a dendritic structure without the formation of granular interdendritic regions. For mechanical properties, the as-cast FeCoNiCrAl0.8Cu0.5Si0.5 alloy demonstrated higher hardness than the as-deposited alloy, with values of 586 HV0.2 and 557 HV0.2, respectively. The wear rate for the as-cast alloy was observed at 3.5 × 10−7 mm3/Nm, with abrasive wear being the primary wear mechanism. Conversely, the as-deposited alloy had a wear rate of 9.0 × 10−7 mm3/Nm, characterized by adhesive wear. The cast alloy exhibited an icorr of 4.062 μA·cm−2, with pitting as the form of corrosion. The laser-deposited alloy showed an icorr of 3.621 μA·cm−2, with both pitting and intergranular corrosion observed. The laser-deposited alloy demonstrated improved corrosion resistance. The investigation of their microstructure and mechanical properties demonstrates the application potential of FeCoNiCrAl0.8Cu0.5Si0.5 alloys in scenarios requiring high hardness and enhanced wear resistance.

A study on microstructure and erosion-corrosion performance of Fe–Cr–Ni–B alloy

Influence of Cr on Microstructure and Electrochemical Properties of FeNiMnCuCrx High-entropy Alloy

Effect of Chromium Content on Microstructure, Hardness, and Wear Resistance of As-Cast Fe-Cr-B Alloy

Investigation on two-body abrasive wear behavior and mechanism of Fe–3.0 wt% B cast alloy with different chromium content

Study on the Performance of Fe-Based Alloy Coating on 40Cr Substrate Surface

Effect of chromium content on the erosion-corrosion behavior of Fe-Cr alloy produced by ball milling liner in weakly alkaline slurry

Investigations of Microstructures and Erosion–Corrosion Performance of Cast Boron-Bearing Stainless Steel

Effect of Ni Content on Microstructure, Mechanical Properties, and Abrasion Behavior of Fe-B-C Alloy

Effect of different chromium contents on microstructure and two-body abrasive wear behavior of Fe-Mn-B surfacing alloys

Microstructure, mechanical properties and lead-bismuth eutectic corrosion behavior of FeCrAlTiNb high-entropy alloy coatings

Microstructure, Hardness, Wear Resistance, and Corrosion Resistance of As-Cast and Laser-Deposited FeCoNiCrAl0.8Cu0.5Si0.5 High Entropy Alloy

Effect of boron on microstructure evolution and properties of wear-resistant cast Fe–Si–Mn–Cr–B alloy

Effect of Chromium on Microstructure and Wear Resistance of Fe-Cr-C Hardfacing Alloys

Mechanisms underlying the influence of Co and Ti on the microstructure, mechanical and wear properties of A2/B2 typed AlCrFeNi alloy

Correlation of microstructure, mechanical properties and corrosion behavior in a Ni34Co28Cr28Al10 multi-principal element alloy with outstanding corrosion resistance

Microstructure and Properties of Fe–Cr–B–Al Alloy After Heat Treatment

Microstructure and Properties of Casting Fe–Cr–B Alloy After Quenching Treatment

Influence of Ni and Cr on Anti-corrosion Performance of Tungsten Carbide Base Hard Alloy

Microstructure and Wear Resistance of FeCoNiCr0.2B0.2 Alloy Prepared by Magnetic Field-Assisted Laser Cladding on Ti-6Al-4V Alloy

Microstructure, abrasive wear and corrosion characterisation of laser metal deposited Fe-30Cr-6Mo-10Ni-2.2C alloy

Microstructure and Tribological Behaviour of CrCuFeNiTi High Entropy Alloys