Abstract:In this study, the effect of Cr content on microstructure and electrochemical measurement of low alloy steel in 3.5 wt% NaCl solution was investigated using scanning electron microscope (SEM), X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical workstation, and the CCT curves of the samples were calculated using JMatPro software. The results showed that the augmentation of Cr content inhibits the formation of ferrite and promotes the development of cementite in low alloy steels. And the reduction of Ar3 (the temperature at which austenite transforms to ferrite) and the increase in Ar1 (the temperature at which ferrite transforms to pearlite) also contribute to the expansion of the pearlite area. The XRD results show that the samples primarily consist of Fe-Cr solid solution with a body-centered cubic structure. As the Cr content increases, the peaks corresponding to the (110), (200), and (211) planes gradually enhance which means the improvement in the crystallinity of the samples. The improvement in the crystallinity can result in a decrease of grain size. Due to the suitable ratio of cementite to pearlite and the synergistic effect of grain size refinement, the Cr2 sample exhibits the best tensile property when the Cr content is 0.970 wt%. Cr(OH)3 and Cr2O3 with protective effects are generated in the corrosion film on the surface of Cr-containing low-alloy steels. And Cr also promotes the transformation of γ-FeOOH to α-FeOOH in the corrosion film because of the atomic radius of Cr3+ being smaller than that of Fe3+. These substances enhance the ability of the corrosion film to block corrosive media and protect the matrix. The results of the electrochemical measurement showed that the increasing Cr content from 0.970 to 4.657 wt% resulted in the enhancement of steel's corrosion resistance. The Cr4 sample exhibits the best corrosion resistance when the Cr content is 4.657 wt%.

Effect of chromium content on the erosion-corrosion behavior of Fe-Cr alloy produced by ball milling liner in weakly alkaline slurry

A study on microstructure and erosion-corrosion performance of Fe–Cr–Ni–B alloy

Effect of different chromium contents on microstructure and two-body abrasive wear behavior of Fe-Mn-B surfacing alloys

Effect of Chromium on Microstructure and Wear Resistance of Fe-Cr-C Hardfacing Alloys

Effect of Chromium on Erosion-Corrosion Properties of ZrO2-Al2O3 Particles Reinforced Fe-based Composites in Artificial Seawater Slurries

Influence of Cr on Microstructure and Electrochemical Properties of FeNiMnCuCrx High-entropy Alloy

Effect of Chromium Content on Microstructure, Hardness, and Wear Resistance of As-Cast Fe-Cr-B Alloy

Understanding Effects of Cr Content on the Slurry Erosion Behavior of High-Cr Cast Irons Through Local Property Mapping and Computational Analysis

Influence of 4 Wt.% Cr Addition on the Corrosion-Wear Synergistic Effect for Al2o3/Fe(Al) Composites

Effect of Chromium-Induced (fe, Cr)3C Toughness Improvement on the Two-Body Abrasive Wear Behaviors of White Cast Iron

The Effect of Chromium Content on the Corrosion Behavior of Ultrafine-Grained CrXMnFeCoNi High- Entropy Alloys in Sulfuric Acid Solution

Investigating the effect of Cr content on the microstructure and electrochemical measurement of low alloy steel

Effect of alloyed Cr on corrosion behavior of low‐alloy steel in wet atmosphere

The Effect of Surface Enriched Chromium and Grain Refinement by Ball Milling on Corrosion Resistance of 316l Stainless Steel

Effect of Cr Content on Microstructure, Mechanical, and Corrosion Properties of CoCr X FeMnNi High-Entropy Alloys Fabricated by Selective Laser Melting

Effects of Chromium Addition on Microstructure and Abrasion Resistance of Fe–B Cast Alloy

Effect of 4 wt.% Cr on microstructure, corrosion resistance and tribological properties of Fe3Al-20 wt.%Al2O3 composites

Microstructure of FeCrAl Thin Film Composed of Nanocrystals Deposited on Zr Alloy and Their Corrosion Behavior under Water Steam Atmosphere.

Investigation on two-body abrasive wear behavior and mechanism of Fe–3.0 wt% B cast alloy with different chromium content

Hardness and Corrosion Behavior of CrMnFeCoNi Alloy Fabricated by Ball Milling and Spark Plasma Sintering

Uniform Corrosion Behavior of FeCrAl Alloys in Borated and Lithiated High Temperature Water