Abstract:A novel designed Ni48Co33Cr9Mo4W6 multi-principal element alloy (MPEA) with single face-centered cubic (FCC) solid-solution phase was fabricated by casting, homogenization, cold rolling, and various post deformation annealing (PDA) heat treatments. The single-phase FCC structured samples with homogeneous grains exhibited average grain sizes ranging from similar to 1.4 to similar to 47.8 mu m. In addition, a single-phase FCC structured heterogeneous sample consisting of partially un-recrystallized region (similar to 47.1 vol%) and fully recrystallized region (similar to 52.9 vol%) was also achieved. Among all the samples with homogeneous grains, the sample processed using PDA treatment at 900 degrees C for 3 min (named as PDA900-3min) showed an average grain size of similar to 1.4 mu m, displaying the best mechanical properties. In detail, it exhibited a yield strength of similar to 811 MPa and a total elongation of similar to 40.2 % at ambient temperature (298 K), and these values were increased to similar to 1085 MPa and similar to 42.7 % at LN2 (77 K) temperature. Due to heterogeneous deformation induced (HDI) strengthening, the hetero-structured sample (named as PDA900-90s) present markedly higher strength and slightly lower ductility in comparison with the PDA900-3min sample at 298 K and 77 K. These two samples demonstrated synergetic improvement of strength and ductility through Mo/W co-doping and PDA heat treatments both at ambient and LN2 temperatures, attributing to solid solution strengthening and grain boundary strengthening, as well as heterogeneous deformation induced (HDI) strengthening. Additionally, Mo/W co-doping, reduces the stacking fault energy (SFE) of the alloy, facilitates the generation of stacking faults (SFs) and twins, which is prone to maintaining the higher work hardening rate. Therefore, our work suggests that Mo and W co-doping is an effective strategy for achieving enhanced strength-ductility synergy in FCC structured MPEAs.

Correlation of microstructure, mechanical properties and corrosion behavior in a Ni34Co28Cr28Al10 multi-principal element alloy with outstanding corrosion resistance

Corrosion resistance improvement of multi-principal element alloy by tailored structure with heterogeneous grains

Simultaneously Improving Strength and Corrosion Resistance of CoCrNi-based Multi-Principal Element Alloys Via Alloying with Mo Content

Enhancing Mechanical and Anti-Corrosion Properties in a L12 Nanoprecipitates Reinforced Fe35.4Ni24Cr21Co9Mo2Cu1.6Al3Ti4 Multi-Principal Element Alloy Via Tailoring Grain Size

Influence of Partial Substitution of Cr by Al on Microstructure and Mechanical Behavior of Fe30Ni35Cr35 Multi-Principal Element Alloy

Exceptional Combination of Mechanical Properties and Cavitation Erosion-Corrosion Resistance in a Fe23.7co23.8ni23.8cr23.7mo5 Multi-Principal Element Alloy

Corrosion of Ru-Free Ni-Fe-Cr-Mo-W-X Multi-Principal Element Alloys

Microstructural evolution, mechanical and corrosion behavior of an Al7.5Co20.5Fe24Ni24Cr24 high‐entropy alloy

High Strength NiMnFeCrAlCu Multi-Principal-element Alloys with Marine Application Perspective

A Novel Martensitic-Like Transformation Fe-Based Multi-principal Element Alloy

Microstructural Evolution, Mechanical Properties, and Corrosion Behavior of an Al7.5Co20.5Fe24Ni24Cr24 High‐Entropy Alloy

Mechanical properties and corrosion resistance characterization of a novel Co36Fe36Cr18Ni10 high-entropy alloy for bioimplants compared to 316L alloy

Influence of interstitial carbon content on the microstructure, mechanical and electrochemical corrosion properties of CoFeNiMn multi-principal component alloys

Microstructure and Corrosion Behavior of AlCoCrFeNiSi0.1 High-Entropy Alloy

Microstructure and Properties of Multi-principal Elements Alloy AlCrMnFeNiCu_x

Strength-ductility Synergy and Superior Strain-Hardening Ability of Ni38Co25Fe13Cr10Al7Ti7 Multi Principal Element Alloy Through Heterogeneous L12 Structure Modulation

Comparative Study of Mechanical and Corrosion Behaviors of Cost-Effective AlCrFeNi High Entropy Alloys

Microstructure, mechanical properties and corrosion resistance of an as-cast fine-structure Cr-Fe-Ni-Al-Si high entropy alloy with Mo addition

Microstructure and Mechanical Properties of an Fe-20Mn-11Al-1.8C-5Cr Alloy Prepared by Powder Metallurgy

Effect of Interstitial Carbon and Nitrogen on Corrosion of FeCoCrNi Multi-Principal Element Alloys Made by Selective Laser Melting

Enhanced Strength-Ductility Synergy in a Mo and W Co-Doping Nicocr Multi-Principal Element Alloy at Ambient and Cryogenic Temperatures