Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Polymer solar cell based on doped o-anthranilic acid and o-aminophenol copolymer

Design and synthesis of high-performance polymer blend solar cell

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

Self-Assembled Amphiphilic Block Copolymers/Cdte Nanocrystals for Efficient Aqueous-Processed Hybrid Solar Cells

Polymeric Solar Cell with 19.69% Efficiency Based on Poly(o-phenylene diamine)/TiO2 Composites

Poly(acrylamide-co-acrylic acid)-based gel polymer electrolytes incorporated with sodium iodide for dye-sensitized solar cells (DSSCs)

Efficient and Stable Quasiplanar Heterojunction Solar Cells with an Acetoxy-Substituted Wide-Bandgap Polymer

Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network Morphology

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

CSA Doped Poly(aniline-co-o-toluidine) and Dispersed Zinc Oxide Nanoparticles: a Promising Material for Photovoltaics

Modulating the nanoscale morphology on carboxylate-pyrazine containing terpolymer toward 17.8% efficiency organic solar cells with enhanced thermal stability

A simple nanostructured polymer/ZnO hybrid solar cell—preparation and operation in air

Copolymers of perylene diimide with dithienothiophene and dithienopyrrole as electron-transport materials for all-polymer solar cells and field-effect transistors

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Aza[5]helicene‐Derived Semiconducting Polymers for Improved Performance in Perovskite Solar Cells: Exploring Energetic and Morphological Influences

A High‐Mobility Low‐Bandgap Copolymer for Efficient Solar Cells

All-Polymer Solar Cells Based on A Blend of Poly[3-(10-N-Octyl-3-Phenothiazine-Vinylene)Thiophene-Co-2,5-Thiophene] and Poly[1,4-Dioctyloxyl-P-2,5-Dicyanophenylenevinylene]

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

All-polymer solar cells based on PTACs/P3HT blends with large open-circuit voltage

Design and fabrication of high-performance poly (p-phenylene azomethine) films for advanced organic photovoltaic applications