Abstract:Interfacial heat transfer resistances during the solidification of aluminum-magnesium alloy strips were measured using the IHCP (Inverse Heat Conduction Problem) method. For these experiments, a small simulator of a single belt caster was used and interfacial heat fluxes and heat transfer coefficients were obtained assuming unidirectional heat flow. The influence of thermophysical properties of substrate, melt superheat and roughness of substrates on strip microstructures in the longitudinal and transverse directions were also investigated. Experimental studies revealed that low superheats (∼ 2 °C) produced finer grain sizes (∼40μm) and homogeneous microstructures were obtained. High thermal conductivity substrates such as copper resulted in strips that were more uniform in thickness and had improved surface quality. It was also found that there was a critical substrate roughness which provided more nucleation sites at the metal/substrate interface resulting in a fine grain distribution throughout the strip produced. On a mesuré les résistances de transfert de chaleur d’interface lors de la solidification de bandes d’alliage d’aluminium-magnésium en utilisant la méthode IHCP (problème de conduction de chaleur inverse). Pour ces expériences, on a utilisé un petit simulateur d’équipement à couler à bandechargeur unique et on a obtenu les flux de chaleur d’interface et les coefficients de transfert de chaleur, en assumant un flot de chaleur unidirectionnel. On a aussi étudié l’influence des propriétés thermophysiques du substrat, de la surchauffe du bain ainsi que de la rugosité des substrats sur les microstructures de la bande tant dans la direction longitudinale que transverse. Les études expérimentales ont révélé que de faibles surchauffes (∼2 °C) produisaient des tailles de grain plus fines (∼40 μm) et qu’on obtenait des microstructures homogènes. Les substrats à haute conductivité thermique tel que le cuivre résultaient en bandes qui étaient plus uniformes en épaisseur et qui avaient une qualité de surface améliorée. On a aussi trouvé qu’il y avait une rugosité critique du substrat qui fournissait plus de sites de nucléation à l’interface métal/substrat résultant en une distribution de grains fins dans toute la bande produite.

Twin roll casting of copper alloy C19210 using commercial scale machine

Inline Hot Rolling of Al-5%Mg Strip Cast Using an Unequal Diameter Twin-Roll Caster

Mechanism of and Key Technologies for Copper Bonding in the Hot Rolling of SCR Continuous Casting and Rolling

Numerical Simulation of Cast-rolling Process for Copper-Aluminum Composite Plate

Effect of the rolling speed on the flow field and solidification welding line of the roll casting for AZ31 magnesium alloy

Melt flow, solidification structures, and defects in 316 L steel strips produced by vertical centrifugal casting

New Technique of Casting-rolling Strips for Semi-solid Magnesium Alloys

Solidification Behaviour and Viscoplastic Deformation in the Strip Casting Process by Twin Roll Method.

Formation Mechanism and Main Control Methods of Bright‐Band Defects in Strip Casting Based on Numerical Simulation

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Superplastic Forming Ability of As‐cast AZ91 Mg Alloy Prepared by Twin Roll Casting

Influence of Process Parameters on Twin Roll Cast Strip of the Alloy AZ31

Microstructure evolution and precipitation behaviour of the Cu-Ni-Si-Cr alloy based on twin-roll strip casting

Formation of the primary structure of cast slabs from aluminum alloys during their twin-roll casting

Preparation and properties of copper-aluminum composite strips and foils by horizontal continuous composite casting and rolling

Effect of Casting Parameters on the Microstructural and Mechanical Behavior of Magnesium AZ31-B Alloy Strips Cast on a Single Belt Casting Simulator

A study on the microstructural evolution of copper/aluminum composite strips fabricated by micro flexible rolling

Studies of Interfacial Heat Transfer Resistances and Characterization of Strip Microstructures for Al-Mg Alloys Cast on a Single Belt Casting Simulator

Microstructure and mechanical properties of pure copper plate processed by novel dynamic offsets and shear force adjustment rolling

Effectively mitigated macro-segregation and improved tensile properties of twin-roll casting Al-Cu strips via the addition of TiC nanoparticles

Study on Manufacturing Technology of Ultra-Thin/Narrow Bonding Cu Strip for Electronic Packaging