Abstract:For titanium matrix composites (TMCs) with a dual-phase structure, yield strength (YS) is typically governed by the hard α phase rather than the soft β phase in the matrix alloy. Therefore, by controlling the precipitation of nanoscale secondary α phases (α s ) within the β phase, lattice distortion can be induced, leading to dislocation pile-ups at the α s /β phase interface, thereby achieving strengthening of the matrix interface. Herein, TiC/TA19 composites were fabricated using spark plasma sintering, and induced the dispersion and pinning of nanoscale α s phases from the β phase at the α s /β phase interface through multi-pass cumulative rolling, achieving super high strength. In particular, the nanoscale α s phase exhibits two typical Burgers orientation relationships with the β phase, i.e. (0001) α s//(110) β & [11 2− 0] α s//[ 1− 11] β and (0001) α s//(01 1− ) β & [11 2− 0] α s//[ 1− 11] β , respectively. Compared with the yield strength of sintered composites, when the rolling reduction was 75 %, the YS of TiC/TA19 composites increased by 33.7 %, reaching 1368 MPa, and the elongation was 3.6 %, only 0.7 % lower than that of sintered composites (4.3 %). The enhanced strength is mainly attributed to the α s precipitation for α s /β interface strengthening and dislocation strengthening derived from the TiC and nanoscale α s precipitates. The volume fraction of dynamic recrystallization grains in TiC/TA19 composites increased with the rolling reduction, and more pyramidal slip systems were activated to coordinate the plastic deformation of the composites. This study offers a promising route to fabricating superior high-strength TMCs and provides new insights into balancing strength and ductility.

Effectively mitigated macro-segregation and improved tensile properties of twin-roll casting Al-Cu strips via the addition of TiC nanoparticles

Synergistic effects of the TiC nanoparticles and cold rolling on the microstructure and mechanical properties of Al–Cu strips fabricated by twin-roll casting

The effect of the TiC-TiB 2 nanoparticles on the microstructure and mechanical properties of Al-Mn-Si strips fabricated by twin-roll casting

Versatility of trace nano-TiC–TiB2 in collaborative control of solidification-rolling-welding microstructural evolution in Al–Mg–Si alloy for enhanced properties

Increased tensile strength and elongation of the Ni–Fe based polycrystalline cast superalloy via the trace addition of TiC nanoparticles

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Strength and ductility enhancement of twin-roll cast Al-Zn-Mg-Cu alloys with high solidification intervals through a synergistic segregation-controlling strategy

Effects of Al-Ti-C Refiner and Forming Processes on the Microstructure and Properties of Al-Zn-Mg-Cu Alloys

Improved Strength-Ductility of Ti-6Al-4V Casting Alloys with Trace Addition of TiC-TiB2 Nanoparticles

Effect of Mg and Si contents and TiC nanoparticles on the center segregation susceptibility of twin-roll cast Al-Mg-Si alloys

Significantly improved strength of the TiC/TA19 composites via interface and dislocation strengthening

Improving element uniformity and mechanical properties of Al–Mg–Si alloy fabricated by twin roll casting with superheat melt treatment

Enhancing mechanical properties of twin-roll cast Al–Mg–Si–Fe alloys by regulating Fe-bearing phases and macro-segregation

Microstructure evolution and enhanced mechanical properties in Al-Mn alloy reinforced by B-doped TiC particles

Investigation of the mechanical properties of TiC particle-reinforced Al-Cu alloys: insights into interface precipitation mechanisms and strengthening effects

Effect of TiC Nano-treating on the Fluidity and Solidification Behavior of Aluminum Alloy 6063

Novel method to achieve synergetic strength–ductility improvement of Al–Cu alloy by in situ TiC–TiB2 particles via direct reaction synthesis

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Microstructure and mechanical properties of Al-Cu alloy during wire and arc additive manufacturing by adding micron TiB2 particles