Abstract:Ti–6Al–4V alloy samples with two bi-lamellar microstructures were prepared by cost-effective thermomechanical powder consolidation and two inter-critical annealing treatments; one comprising of annealing at 900 °C followed by air cooling (900-AC alloy) and the other comprising of annealing at 910 °C followed by water quenching and aging (910-Q&A alloy), respectively. Both bi-lamellar microstructures encompass lamellae of primary α phase and β transformed structure which consists of ultrathin secondary α lamellae and β thin layers. Thanks to the higher Al concentration in the primary α lamellae associated with the higher annealing temperature and finer scale of βt structure lamellae, the α and βt lamellae of the 910-Q&A alloy exhibit a higher nano-hardness than that of the 900-AC alloy (5.4 and 4.6 GPa vs. 4.5 and 4.3 GPa) as well as a larger difference in nano-hardness between the α and βt lamellae (0.8 vs. 0.2 GPa). These microstructural and nano-hardness differences lead to a significant enhancement of the yield strength of the 910-Q&A alloy by 200 MPa compared to the 900-AC alloy with almost no decrease of tensile ductility. Quantitative analysis indicates that the hardening of α and βt lamellae accounted for approximately 35% and 28% of the total strength increment, respectively, while the heterostructure induced hardening associated with the inhomogeneity between the α and βt lamellae accounts for approximately 37% of the strength increment. Interestingly, the significantly higher flow stress of the 910-Q&A alloy during tensile deformation induces a significant higher degree of trans-lamellar twinning which is believed to be responsible for mitigating the strain localization and maintaining the good tensile ductility despite of a higher flow stress.

Improved Strength-Ductility of Ti-6Al-4V Casting Alloys with Trace Addition of TiC-TiB2 Nanoparticles

Increased tensile strength and elongation of the Ni–Fe based polycrystalline cast superalloy via the trace addition of TiC nanoparticles

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Simultaneously enhanced strength and toughness of cast medium carbon steels matrix composites by trace nano-sized TiC particles

Versatility of trace nano-TiC–TiB2 in collaborative control of solidification-rolling-welding microstructural evolution in Al–Mg–Si alloy for enhanced properties

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Strengthening behavior of B doped TiC particles on an Al–Zn–Mg alloy

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Role and mechanism of innovative addition process of trace nano-TiC p in microstructure manipulation and significant mechanical properties enhancement of H13 steels

Promoting Strengthening and Grain Refinement of Aluminum Alloy During Wire and Arc Additive Manufacturing by Adding TiB2 Particles

Novel method to achieve synergetic strength–ductility improvement of Al–Cu alloy by in situ TiC–TiB2 particles via direct reaction synthesis

Enhancing strength-ductility synergy in nano-sized TiB 2 /Al composite via rapid solidification and thermo-mechanical processing

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Construction of Three-Dimensional Network Morphology Titanium Matrix Composites Via Adding Nano B4C: As-built and Heat-Treated Scenarios

A Newly Generated Nearly Lamellar Microstructure in Cast Ti-48Al-2Nb-2Cr Alloy for High-Temperature Strengthening

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Additive manufacturing of a nanocrystalline lathy Ti6Al4V5Cu alloy with high strength and ductility combination

Strength enhancement of a bi-lamellar PM Ti–6Al–4V alloy without sacrificing ductility by Al partitioning and twinning-induced plasticity effect

Effectively mitigated macro-segregation and improved tensile properties of twin-roll casting Al-Cu strips via the addition of TiC nanoparticles