Abstract:The common problem of low strength-ductility matching prevails in near-α high-temperature titanium matrix composites (TMCs). In this work, the design strategy of ultrafine grains and dispersed (Ti, Zr)6Si3 nanoprecipitates in the microstructure of TiBw/near α-Ti composites via low-temperature isothermal multidirectional forging (IMDF), is expected to break the trade-off dilemma between strength and ductility. The results show that with the decrease in the temperature of IMDF, the grain scale decreased from 0.98 μm to 0.59 μm, and the location of silicide precipitation shifted from phase boundaries and grain boundaries to α-grain boundaries and intracrystalline regions. The experiments confirm that the local segregation of Si and the temperature of thermomechanical deformation are the key factors affecting the precipitation behavior of silicides. With the decrease of the deformation temperature, the precipitation mechanism of silicides changes from a single diffusion-controlled precipitation to the coupling of two mechanisms, namely, elemental diffusion and dislocation-assisted nucleation, which facilitates the successive precipitation of nanometer-sized silicides at the grain boundaries and in the inner regions. The ultimate tensile strength (UTS) and elongation of the composites were substantially increased after IMDF at 950 and 800°C, especially the excellent performance at 800°C, where the strength reached 1320.3 MPa and the elongation was 5.8%. The room and high-temperature strengthening and failure mechanisms of the composites are analyzed and discussed, and the yield strength (YS) increments provided by various strengthening mechanisms at room temperature are quantified, aiming to provide a potential preparation strategy for the synergistic strengthening of near-α TMCs with ultrafine grains and nanoparticles.

Enhancing strength-ductility synergy in nano-sized TiB 2 /Al composite via rapid solidification and thermo-mechanical processing

On the Study of a TiB2 Nanoparticle Reinforced 7075al Composite with High Tensile Strength and Unprecedented Ductility

Achieving High Strength-Ductility Synergy in TiBw/near Α-Ti Composites by Ultrafine Grains and Nanosilicides Via Low-Temperature Severe Plastic Deformation

Enhancing Strength-Ductility Synergy and Mechanisms of Al-based Composites by Size-Tunable In-Situ TiB2 Particles with Specific Spatial Distribution

Effect of In-Situ TiB2 Particles on Microstructure and Mechanical Properties of Al–Fe–Ni Manufactured by Selective Laser Melting

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB2/Al-Cu-Mn Composites

Superior Strength and Ductility of In Situ Nano TiB2/Al-Cu-Mg Composites by Cold Rolling and Post-Aging Treatment

Microstructure Manipulation and Strengthening Mechanism of TiAl Composites Reinforced by Cr Solid Solution and In-Situ Nanometer-Sized TiB2 Particles

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB<sub>2</sub>/Al-Cu-Mn Composites

Effects of Nanosized Particles on Microstructure and Mechanical Properties of an Aged In-Situ TiB2/Al-Cu-Li Composite

A New Approach for Improving the Elevated-Temperature Strength and Ductility of Al–Cu–Mg–Si Alloys with Minor Amounts of Dual-Phased Submicron/nanosized TiB2–TiC Particles

Superior Strength-Ductility Combination in Tic/Tc4 Composites Via in Situ Construction Ti2cu Nanoparticles

Synergistically Enhanced Strength and Ductility of TiB/(TA15-Si) Composites: A Two-Step HIP Strategy

Achieving Simultaneously Improved Tensile Strength and Ductility of a Nano-Tib2/alsi10mg Composite Produced by Cold Spray Additive Manufacturing

Enhancing strength and ductility of AlSi10Mg fabricated by selective laser melting by TiB2 nanoparticles

Effect of an Improved Multistage Thermo-Mechanical Processing on Microstructure and Mechanical Property of TiB2/Al-Cu Composites

Microstructure and Mechanical Properties of In-Situ TiB2/AlSi7Mg Composite Via Powder Metallurgy and Hot Extrusion

Microstructure Refinement and Strengthening Mechanisms of Bimodal-Sized and Dual-Phased (Ticn-Al3tim)/al Hybrid Composites Assisted Ultrasonic Vibration

Effect of Nano-Tic/tib2 Particles on the Recrystallization and Precipitation Behavior of AA2055-TiC+TiB2 Alloys

Superior strength-ductility combination in TiC/TC4 composites via In situ construction Ti 2 Cu nanoparticles

Microstructure and mechanical properties of an in-situ TiB 2 /Al-Zn-Mg-Cu-Zr composite fabricated by Melt-SHS process