Abstract:With excellent specific strength, specific modulus and service performance at high temperature, TiAl-based alloys have become the key material for the update of aerospace engineering. However, the coarse as-cast grain size, low room temperature plasticity and strength limit their further engineering application. In this paper, the Ti-48Al-2Cr-2Nb ingot alloyed with TiB2 and Ni was prepared by the induction melting, and the effects of TiB2 and Ni on the solidification microstructure and mechanical properties were studied. The results show that the addition of TiB2 and Ni exhibits little influence on the solidification path and primary phase. The grain size is refined from 700 mu m to 100 mu m, and the flake TiB2 and Ni-riched tau(3) phase is determined. The nanohardness of tau(3) phase is detected as 8.3 GPa, which is significantly higher than that of lamellar colony and bulk gamma phase. Tensile strength of T4822-(Ni,TiB2) alloy is similar to that of the matrix alloy, and the fracture elongation is increased by 30% at room temperature. At 700 similar to 900 degrees C, T4822-(Ni,TiB2) alloy shows the preferable tensile strength, and the tensile strength at 900. reaches 365 MPa, 9% higher than that of the matrix alloy. At 800 and 900 degrees C, the breaking elongation reaches 25.3% and 36.1%, respectively, much higher than that of the matrix alloy. The refinement of grain size and the massive gamma phase at grain boundary are the main reasons for the plasticity improvement of T4822-(Ni,TiB2) alloy. And the good high temperature strength can be attributed to the hard borides and Ni-rich tau(3) phase inside and at the interface of lamellar masses.

Increased tensile strength and elongation of the Ni–Fe based polycrystalline cast superalloy via the trace addition of TiC nanoparticles

Improved Strength-Ductility of Ti-6Al-4V Casting Alloys with Trace Addition of TiC-TiB2 Nanoparticles

Effectively mitigated macro-segregation and improved tensile properties of twin-roll casting Al-Cu strips via the addition of TiC nanoparticles

Simultaneously enhanced strength and toughness of cast medium carbon steels matrix composites by trace nano-sized TiC particles

Reaction-induced nano-sized TiC in additive manufactured Ni-Co based superalloy

Simultaneously Improved the Strength and Ductility of Cast Al-3Li-2Cu Alloy by Ti Addition and Heat Treatment

Enhanced tensile properties in a Cu-Al2O3 alloy via trace Ti addition

Cracking inhibition of nano-TiC reinforced René 104 superalloy fabricated by selective laser melting

The Enhancement Effect of Carbides on the Printability and Mechanical Properties of a Ni–Fe–Cr–Al–Ti Alloy Processed by Electron Beam Freeform Fabrication

Microstructure Evolution and Tensile Properties of Conventional Cast TiAl-based Alloy with Trace Ni Addition

Study on the Dissolution and Precipitation Behavior of Self-Designed (NbTi)C Nanoparticles Addition in 1045 Steel

Role and mechanism of innovative addition process of trace nano-TiC p in microstructure manipulation and significant mechanical properties enhancement of H13 steels

Effect of In-Situ Nanoparticles Induced by Ti Addition on the Microstructure and Tribological Properties of FeCrB Alloys

Versatility of trace nano-TiC–TiB2 in collaborative control of solidification-rolling-welding microstructural evolution in Al–Mg–Si alloy for enhanced properties

Control of a fine-grained microstructure for cast high-Cr TiAl alloys

Effects of Titanium Addition on the Microstructural and Mechanical Property Evolution of FeCrB Alloys

Effects of Titanium Addition on Microstructure and Mechanical Properties of CrFeNiTix (x = 0.2–0.6) Compositionally Complex Alloys

Microstructure and mechanical properties of aluminum alloy composites with endogenous nano-TiCp

Solidification Microstructure Evolution and Mechanical Properties of Casting Ti-48Al-2Cr-2Nb-(Ni,TiB2)Alloy

Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Improvement of the high temperature oxidation of TaC-strengthened Co(Cr)-based cast superalloys by the addition of nickel