Abstract:A low-resistivity titanium silicide (TiSi 2 ) is crucial as a gate and source/drain material in microelectronic device fabrication, offering notable properties to enhance device performance. This study aims to experimentally determine the optimum process parameters, including arsenic doping dosage, titanium thickness, and two-step rapid thermal process (RTP) temperature, for the sheet resistance of titanium self-aligned silicide process using a design of experiment methodology. The results demonstrate that both the thickness of the titanium and the temperature of the RTP play crucial roles in determining the sheet resistance of TiSi 2 . Statistical analysis reveals that increasing the titanium thickness or the temperature of the first-step RTP (RTP-1) could reduce the sheet resistance. Additionally, an optimal second-step RTP (RTP-2) temperature is critical to yield low-resistivity TiSi 2 by completely converting C49- to C54-phase. The optimum process conditions for obtaining low sheet resistance are a titanium thickness of 32-35 nm, RTP-1 temperature of 720-750°C for 75 s, and RTP-2 temperature of 860°C for 20 s. Moreover, surface amorphization of the polysilicon by arsenic ion implantation before the deposition of Ti/TiN films also plays a crucial role in the formation of C54-TiSi 2 . The lowest sheet resistance achieved was 3.91 Ω/sq with an arsenic dosage of 1 × 10 14 cm -2 . The optimum condition was adopted for forming a submicron polysilicon gate, providing a promising approach for designing the process parameters for titanium self-aligned silicide formation to achieve low resistance in nanoscale electronic devices.

Improvement of contact resistivity of titanium silicide on P-doped epitaxial Si using a Se interlayer

Pre-deposition Growth of Interfacial SiO2 Layer by Low-Oxygen-partial-pressure Oxidation in the Al2O3/4H-SiC MOS Structure

Surface-Morphology Study of Titanium Silicide Formed on Polycrystalline Silicon

Improving the barrier inhomogeneity of 4H-SiC Schottky diodes by inserting Al2O3 interface layer

Titanium Silicide: A Promising Candidate of Recombination Layer for Perovskite/Tunnel Oxide Passivated Contact Silicon Two-Terminal Tandem Solar Cells

Process optimization of titanium self-aligned silicide formation through evaluation of sheet resistance by design of experiment methodology

Titanium Contacts to MoS2 with Interfacial Oxide: Interface Chemistry and Thermal Transport

Electrical Properties Of The Tisi2-Si Transition Region In Contacts: The Influence Of An Interposed Layer Of Nb

Low Contact Resistivity of Ti/TiN/Al for NiSi2 on Epitaxial Si:P Structure at Full Low-Temperature Process below 450 °C

Improvement of Er-silicide formation on Si(100) by W capping

Role of ultra-thin tungsten interlayer in blocking nitrogen diffusion and reducing specific contact resistivity in titanium/n+-Si ohmic contacts

Thermal Stability of TiN/Ti/p+-Si0.3Ge0.7 Contact with Ultralow Contact Resistivity

Experimental Investigation of As Preamorphization Implant on Electrical Property of Ti-Based Silicide Contacts

A method to improve the specific contact resistance of 4H-SiC Ohmic contact through increasing the ratio of sp 2 -carbon

A Method to Improve the Specific Contact Resistance of 4H-Sic Ohmic Contact Through Increasing the Ratio of Sp2-Carbon

Ohmic contact formation mechanisms of TiN film on 4H–SiC

Improvement of electrical performance using PtSe2/PtTe2 edge contact synthesized by molecular beam epitaxy

Low resistivity C54 phase TiSi2 films synthesized by a novel two-step method

Suppression of Charge Density Wave by Substrate Induced Doping on TiSe$_2$/TiO$_2$ Heterostructure

Dielectric and Insulating Properties of SrTiO3/Si Heterostructure Controlled by Cation Concentration