Abstract:IN738 superalloy with excellent high-temperature performance is of huge interest for hot-end component applications in aerospace, but its additive manufacturing via selective laser melting (SLM) is rather challenging due to the unsolved high crack susceptibility. Here, for the purpose of improving the formability of IN738 in SLM, Mn + Si content was then strictly controlled in raw powder. An orthogonal experiment was then carried out under different energy inputs to investigate the characteristics of the molten pool, metallurgical defects, microstructures, and mechanical properties of IN738 by SLM. The results showed that high laser power was more likely to shape large melting depth and depth-to-width ratio under the same linear energy density (LED), rather than scanning speed. Four morphologies of the molten pool were observed in the entire LED range. At lower LEDs, hot cracks were usually accompanied by irregular pores due to the stress concentration at the sharp corner of pores; at higher LEDs, cracks were located at the interface of grain boundaries with large misorientation angles. Energy dispersive spectrometry results revealed that the presence of Al-rich oxides and high Mn + Si content at the interface were the main reasons for cracking. The Scheil-Gulliver solidification modeling was used to examine the cracking susceptibility of Si and Mn elements. In addition, both dendrites and cellular dendrites were found in columnar grain structures. By reducing the Mn + Si content and optimizing process, crack-free and nearly fully dense samples of IN738 were obtained by SLM with excellent mechanical properties (ultimate tensile strengths = 1206 MPa, yield strength = 866 MPa and elongation = 16.5%), which were much higher than the mechanical properties of conventionally manufactured IN738.

Effect of Laser Energy Density on Surface Morphology, Microstructure, and Magnetic Properties of Selective Laser Melted Fe-3wt.% Si Alloys

Research on the limitations of laser energy density and microstructure characteristics of selective laser melted AlSi10Mg alloy

Effects of heat treatment on the microstructures and magnetic properties of selective laser melted Fe-3wt.%Si functional soft magnet

CoCr alloy processed by Selective Laser Melting (SLM): effect of Laser Energy Density on microstructure, surface morphology, and hardness

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Magnetic and mechanical properties of additive manufactured Fe-3wt.%Si material

Effect of process parameters on microstructures and properties of Al-42Si alloy fabricated by selective laser melting

Effects of laser power on the microstructural evolution of novel Ti–6Zr–5Fe alloy fabricated by selective laser melting

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Experimental Research on Selective Laser Melting AlSi10Mg Alloys: Process, Densification and Performance

Microstructure and magnetic properties of FeSiBCrC soft magnetic alloy manufactured by selective laser melting

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Influence of Laser Energy Density on Tribological Properties of AlSi10Mg Manufactured by Selective Laser Melting

Selective laser melting of IN738 superalloy with a low Mn+Si content: Effect of energy input on characteristics of molten pool, metallurgical defects, microstructures and mechanical properties

The effect of a remelting treatment scanning strategy on the surface morphology, defect reduction mechanism, and mechanical properties of a selective laser-melted Al-based alloy

Effects of remelting on the surface morphology, microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Effect of Laser Irradiation and Tensile Stress on Microstructure and Magnetic Properties of Fe-Based Amorphous Alloys

Effect of process parameters on the texture evolution of Fe-6.5 wt% Si soft magnetic alloys manufactured via laser powder bed fusion

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

Microstructure and Mechanical Properties of FeCoNiCrAlx High-entropy Alloys by Selective Laser Melting