Abstract:The foamed structure of the central layer, predominantly governed by the addition levels of TiH 2 and the composition of the precursor, in addition to the parameters associated with the foaming process, constitutes the pivotal determinant impacting the spectrum of applications for aluminum foam sandwiches. Systematic research on the foaming behavior of the AlMg 4 Si 8 matrix and pure Al matrix precursors in closed cavities with different TiH 2 addition levels was conducted. The results reveal that with the increasing amount of TiH 2 , specifically at a 200% expansion rate of AlMg 4 Si 8 foams, the number of large pores decreased, the average pore size decreased from 0.67 mm 2 (0.6 wt%) to 0.43 mm 2 (1.0 wt%), and the total number of pores increased from 125 (0.6 wt%) to 156 (1.0 wt%). This trend of pore size consistency was evident not only at the mentioned 200% expansion rate but also across different expansion rates of AlMg 4 Si 8 foams and across all expansion rates of pure Al foams. The pore structures observed in the AlMg 4 Si 8 matrix and pure aluminum matrix foams within a closed cavity exhibited significantly superior characteristics compared to those achieved through free foaming processes. The circularity of pure Al foams was mainly distributed in the range of 1–2, being higher than the AlMg 4 Si 8 foams (1–1.5) due to their low viscosity and foam stability. The compressive curve of AlMg 4 Si 8 foams at a 400% expansion rate reveals that as the average cross-sectional area increased, there was a higher likelihood of experiencing initial collapse conditions. Additionally, the fluctuation of the platform area became more pronounced. Further, the slope corresponding to the elastic stage of the compressive curve increased as the overall stress levels increased.

Influence of Gas Pressure and Blowing Agent Content on the Formation of Aluminum Alloy Foam

Factors affecting the microstructure of a fine ceramic foam

Study on an Aluminum Foam by Gas Injection Foaming

Optimization of Mg Blowing Agent Content for Foaming Aluminum

Preparation of Aluminum Foam by Gas Injection Foaming

Factors Influencing Foam Height in Gas Injection Process for Aluminum Foams

Effects of process parameters and alloy compositions on the pore structure of foamed aluminum

Preparation principle and compression properties of cellular Mg–Al–Zn alloy foams fabricated by the gas release reaction powder metallurgy approach

Aluminum Foam Sandwich: Pore Evolution Mechanism Investigation and Engineering Preparing Optimization

Assessment of the flow behavior and structural performance of open-cell aluminum foams at critical flow conditions of pressure and temperature

Effect of Orifice Diameter on Bubble Generation Process in Melt Gas Injection to Prepare Aluminum Foams

The influence of pure Al and hypoeutectic Al Si alloy base materials on the cell structures of aluminum foams produced by gas injection foaming process

Development of AlMg35-TiH2 composite foaming agent and fabrication of small pore size aluminium foams

Controllable Design of Structural and Mechanical Behaviors of Al‐Si Foams by Powder Metallurgy Foaming

Foaming Process and Properties of 6063 Aluminum Foams by Melt Foaming Method

Influences of Increased Pressure Foaming on the Cellular Structure and Compressive Properties of In Situ Al-4.5%Cu-xTiB2 Composite Foams with Different Particle Fraction

Oxidation Kinetics of Oxide Film on Bubble Surface of Aluminum Foams Produced by Gas Injection Foaming Process

Foaming Behavior of AlMg4Si8 Matrix and Pure Al Matrix Precursors in Closed Cavities with Different TiH2 Addition Levels

Optimization of Cellular Structure of Aluminum Foams Produced by Powder Metallurgy Method

Aluminium foam with sub-mm sized cells produced using a rotating gas injector

Effect of Compaction Pressure on Microstructural, Mechanical, and Thermal Properties of Aluminum Foams Processed through Space-Holder Technique